VL Trans rebuild

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Grumpa
    replied
    Later transmissions like my '69 FLH have the sprocket locknut torqued down to 140-150'#s, so is that the target for the VL? IMG_2268.jpg

    Leave a comment:


  • Grumpa
    replied
    The one thing this forum lacks is a "like" button. Thank you Steve for all your contribution to keeping VLs alive. I timed the starter today IMG_2254.jpg

    Leave a comment:


  • Guest
    Guest replied
    Good info, thanks

    Leave a comment:


  • Steve Slocombe
    replied
    There are numerous manufacturers of sealed bearings and they seem to come in different qualities. The red seals seem softer than the black ones, and we have recently had a red sealed one at the drive end slowly passing oil through the bearing. I would now tend to use good quality sealed bearings and leave in the old brass seals on the principle that they can't hurt and might do some good. With two sealed bearings you don't get end play in the mainshaft, and I screw in the ball bearing holder until the mainshaft locks up, and then back it out half a turn and check the assembly turns freely. The downside from slightly different bearing dimensions is that your original 2500-19 thrust washer under the clutch bearings may need replacing. Harley made them in 0.006" thickness increments so must have thought it was important. Too thin and the clutch can wobble, but too thick and the clutch drum binds and the clutch drags.

    Leave a comment:


  • Guest
    Guest replied
    I see what you mean Grumpa, that’s not much difference. I think I’ll do the same as you unless someone comes up with a reason not to. Thanks for the bearing numbers and thanks to Steve also. Keep up the good work.

    Leave a comment:


  • Grumpa
    replied
    Originally posted by dustydog View Post
    Grumpy can you post the sealed bearing numbers that you used on the main shaft? And did you use a spacer inboard of the right side sealed bearing or not? I seen some discussion about this spacer being needed to maintain correct end play on the main shaft. What did you do? I am in the middle of a trans rebuild also and would like to use the sealed bearings also. Your thread is a great help. Thanks
    De nada Dusty and maybe you're helping me avoid more dumb stuff as I've not heard of adding a spacer to the r/h/s inboard. As a matter of fact I left out both the large and small brass oil retainers as well because I didn't see the need. IMG_2242.jpg

    Going back and measuring I found a difference between old and the new with the new sealed bearing being .006" longer on the left hand. On the right side the difference was .0055" with the new sealed bearing being shorter, so it seems like a wash to me. IMG_2245.jpg But I shall defer to the wisdom of those smarter than I.

    Leave a comment:


  • Steve Slocombe
    replied
    I've also had problems with the early Eastern gearbox mainshafts, which had incorrect angle tapers at both ends. The sealed bearing numbers are on the vlheaven.com Website.

    Leave a comment:


  • Guest
    Guest replied
    Grumpy can you post the sealed bearing numbers that you used on the main shaft? And did you use a spacer inboard of the right side sealed bearing or not? I seen some discussion about this spacer being needed to maintain correct end play on the main shaft. What did you do? I am in the middle of a trans rebuild also and would like to use the sealed bearings also. Your thread is a great help. Thanks

    Leave a comment:


  • Robert Luland
    replied
    The Eastern shafts are a tight fit on the key. I've dealt with this in the past. If your set up for grinding then go for it. I found it was a hell of a lot easier to deal with the key.
    Bob L

    Leave a comment:


  • Grumpa
    replied
    Latest snag is that an aftermarket mainshaft didn't have the starter clutch key ways cut correctly IMG_2240.jpgIMG_2241.jpg. Modifying the OEM keys but now considering pulling the shaft and cutting the shaft.

    Leave a comment:


  • Grumpa
    replied
    So I've shot myself in the foot here. Installed the studs IAW the suggested stud heights with red Loctite. The top long studs @ 11/16" were too short IMG_2224.jpg and destroyed one of them adjusting to 7/8"IMG_2229.jpg. The side studs installed @ 1/2" IMG_2225.jpg adjusted to .6" IMG_2230.jpg. I should have checked before installing with Loctite for crying out loud.

    Leave a comment:


  • Grumpa
    replied
    So prior to the re-build I made a weld fixture: IMG_2210.jpgIMG_2211.jpgIMG_2211.jpgIMG_2212.jpgIMG_2213.jpgIMG_2214.jpg

    Leave a comment:


  • Grumpa
    replied
    Yea! Parts back from cadmium plating IMG_2207.jpg Hat's off to Retrocycle.

    Leave a comment:


  • Grumpa
    replied
    Originally posted by Robert Luland View Post
    45 minutes? When the fizzing stops, the operation is over. Usually 5 to 8 minutes.
    Yeah I wasn't happy with the results and suspected there was something wrong with my process. The instructions were 14 ounces acid to 1 gallon water. So today I went with just straight acid IMG_2190.jpg at 190 degrees + for 5 minutes with much better results IMG_2191.jpg

    Leave a comment:


  • Robert Luland
    replied
    45 minutes? When the fizzing stops, the operation is over. Usually 5 to 8 minutes.

    Leave a comment:

Working...