VL Trans rebuild

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Grumpa
    replied
    Originally posted by Steve Slocombe View Post
    Countershaft gear end float is usually reckoned as free running to 0.010" so you're OK.
    Awesome! I was going by your book IMG_2144_LI.jpg so that's a typo. If you ever want some editing I'll volunteer free of charge if you think you'll come out with another edition.

    On another note, I have a wide selection of clutch bearing thrust washers 2500-19; from .0889 to .1195. What's the goal here? As noted above, something was wrong with the last guy's assembly because the hub was mushroomed and the washer had metal smear. The bearing cage length exceeds the hub.

    Leave a comment:


  • Steve Slocombe
    replied
    Countershaft gear end float is usually reckoned as free running to 0.010" so you're OK.

    Leave a comment:


  • Grumpa
    replied
    So on fitting the clutch; the old mainshaft measured 1.0000 at the clutch 2494-30 race area the new mainshaft is 1.0005. The race measured 1.5005. The bearings were .250. Noted that the 2500-19 roller bearing washer had metal smear IMG_2143.jpg and the race was mushroomed. I replaced the mainshaft and it measures 1.0005 and of course it's a plug fit now with the nominal .250 bearings and 1.5005 race. My plan is to hone out the race another .0005.

    Leave a comment:


  • Grumpa
    replied
    Doing a dry run re-assembly, tranny is good. Bearings were nominal and ended up replacing with oversize on the countershaft. IMG_2105.jpg The L/H were a plug fit at .0008 and I installed .0004. The R/H were a plug fit at .0006 and I installed the 92222 .0004 o/s there as well. The old countershaft thrust washer was .078 and replaced with a .083, a new 2309-32 c/s gear end plate and I still have a .005 end play when it should be .001. Have a 2309-16 c/s bearing collar on the way which will hopefully fix the end play issue. I modified the mainshaft installation with sealed bearings IMG_2115.jpgIMG_2119.jpg so I left the brass oil seals out.
    Last edited by Grumpa; 09-16-2018, 05:39 PM.

    Leave a comment:


  • Grumpa
    replied
    Okay so I installed the shorter 35094-65 bushing midway in the main gear IMG_2083.jpg IMG_2084.jpg as opposed to favoring one side or the other. If someone has another theory, please educate me.

    Leave a comment:


  • Grumpa
    replied
    Originally posted by Steve Slocombe View Post
    Yes, it is the -25 main drive gear which has the spirals cut in the steel, and less wide teeth than the -31 version. The -65 bushing is shorter than the original -31 VL one, but all we can find these days and seems to do the job.
    Originally posted by Peter Cooke View Post
    I think that's actually a 2296-25 main drive gear. Looking at your 5th photo in post#7 and reading Steve's comments in post #10 re the bore sizes you may have your part numbers around the wrong way in your photo.

    It reads like the earlier gear has the smaller ID and needs to be bored to use the later bushing.

    In the earlier set up the bushing was soldered to the mainshaft which would explain the oil passages in the main drive gear.
    Okay now I understand a little better now, thanks! What came out of the tranny was the 2272-30 shaft with the 2296-31 gear, NOT the 2296-25 spiraled gear like you'd expect (thus my confusion). That helps a lot, thank you gentlemen.IMG_2080.jpg

    Leave a comment:


  • Steve Slocombe
    replied
    Yes, it is the -25 main drive gear which has the spirals cut in the steel, and less wide teeth than the -31 version. The -65 bushing is shorter than the original -31 VL one, but all we can find these days and seems to do the job.

    Leave a comment:


  • Peter Cooke
    replied
    I think that's actually a 2296-25 main drive gear. Looking at your 5th photo in post#7 and reading Steve's comments in post #10 re the bore sizes you may have your part numbers around the wrong way in your photo.

    It reads like the earlier gear has the smaller ID and needs to be bored to use the later bushing.

    In the earlier set up the bushing was soldered to the mainshaft which would explain the oil passages in the main drive gear.
    Last edited by Peter Cooke; 08-18-2018, 09:49 PM. Reason: spelling

    Leave a comment:


  • Grumpa
    replied
    Okay so I need some education here. My 2296-31 main drive gear has oil passages: IMG_2077.jpg which would indicate movement relative to the mainshaft bushing 2297-31. Yet the 2297-31 bushing has oil passages on the ID as well which would indicate movement relative to the mainshaft. What am I missing? Is the 35094-31 bushing the same as the 35094-65 split back bushing?

    Leave a comment:


  • Grumpa
    replied
    Originally posted by Peter Cooke View Post
    I've been assuming the Chain Guard Clutch Plate would be gloss black to match the Front Chain Guard inner upper & lower pieces.
    That's pretty much what I figured as well Pete thanks man.
    Originally posted by Steve Slocombe View Post
    They're usually covered in rust and filth when I see them....These are not items which give me sleepless nights.
    Lol me either, it's just that since everything's apart and cleaned up I thought I'd ask. Thanks Steve

    Leave a comment:


  • Steve Slocombe
    replied
    They're usually covered in rust and filth when I see them, and an AMCA judge will need better knees than I've got, plus a penlight torch and a dental mirror, to prove us wrong. I've had a couple of nos dust rings, I think one parkerized and one black enamel, but that does not mean they were made before 1935. Maybe the early ones were flat nickel, then cad around 1930, then parkerized? On the chain guard clutch plates, the 1932-35 brackets look parkerised, but I have one cad, possibly replated. The clutch plate itself is often shiny under all the dirt. Flat nickel, cad or zinc are all possibilities depending when they were made. These are not items which give me sleepless nights.

    Leave a comment:


  • Peter Cooke
    replied
    I've been assuming the Chain Guard Clutch Plate would be gloss black to match the Front Chain Guard inner upper & lower pieces.

    The Clutch Dust ring I have no clue. I had mine CAD plated when I did the g'box lid and kicker cover but it probably should be just parkerised.

    Leave a comment:


  • Grumpa
    replied
    Okay so can anyone say with any certainty what the finish was on the Chain Guard Clutch Plate 3812-30 or 3812-32? Or the 2501-25 Clutch Dust ring?IMG_2074.jpg

    Leave a comment:


  • Steve Slocombe
    replied
    That's it. The later countershaft gear has deeper teeth at the small end to mesh with the 1931-36 main drive gear, and also takes the longer 2306-32 needle rollers to replace the earlier 2289-17 caged rollers. The needle rollers need inner and outer thrust washers. Today you can buy the 2308-16 end plate in various thicknesses to set up the countershaft end float in the case from free running to around ten thousandths. Main problem I've found with the early cluster gears is that the short roller wears well past any available oversizes for rebuilding. Many 1925-30 JD/VL owners are replacing the whole countershaft gear assembly with the 1932-36 style. I also use the 1931-36 unstepped mainshaft to avoid soldering those pesky split bronze bushings.

    Leave a comment:


  • Grumpa
    replied
    So just to document: IMG_2000.jpgIMG_2001.jpgIMG_2001.jpg

    Leave a comment:

Working...