VL Trans rebuild

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • NCriding
    replied
    Grumpa,
    Yes, I was referring to posts 29-33, thanks for the info! Sounds like my antique South Bend lathe is not the tool for the job, I’ll see if the big Jet we have at work will get the job done.
    For such a “simple” gearbox, it appears to have challenged more than a handful of us. In my case, due to the upgrade of using sealed bearings that do not maintain the main shaft and output shaft offsets.

    Leave a comment:


  • Grumpa
    replied
    Originally posted by NCriding View Post
    Would you please provide the part number of the seal you installed in the output shaft? To cut the recess, did you just insert an expanding collete in the bronze bushing?
    NCriding,
    I believe I used seal 12022 if you're referring to the seal added in post #29 - #33. Modifying the gear was alas, beyond the capacity of my little benchtop so I had a buddy at work do the deed. He noted that the gear was "hard as fuk" and whatever he did ended up with a pretty loose fit to the seal

    Glad you enjoyed the thread - like I might have mentioned earlier; it takes an entire village to raise this idiot.

    Leave a comment:


  • NCriding
    replied
    Thank you! Enjoyed reading your trans build story and learned a lot from it.

    Leave a comment:


  • 34VLRay
    replied
    Harley-Davidson part #12035B seal for output shaft. Works well on 31 up

    Leave a comment:


  • NCriding
    replied
    Grumpa,
    Would you please provide the part number of the seal you installed in the output shaft? To cut the recess, did you just insert an expanding collete in the bronze bushing?
    Thanks!
    NC riding

    Leave a comment:


  • sny
    replied
    Originally posted by sny View Post
    Thanks for the insight 34VLRay, Ill give it a try
    Follow up for future reference:
    A thinner thrust washer along with light filing and cleanup of the drive disc hub side fixed my problem shifting into first.

    Leave a comment:


  • sny
    replied
    Originally posted by 34VLRay View Post
    That’s usually the problem when they won’t go into gear without grinding. Replace thrust washer with thinner one or grind .005 thousandth off.
    Thanks for the insight 34VLRay, Ill give it a try

    Leave a comment:


  • Peter Cooke
    replied
    Hi Ray,

    I sent you a PM a couple of months back. Just wondering if it got to you?

    Peter

    Leave a comment:


  • 34VLRay
    replied
    That’s usually the problem when they won’t go into gear without grinding. Replace thrust washer with thinner one or grind .005 thousandth off.

    Leave a comment:


  • sny
    replied
    This is a great thread! Lots of hidden tips for the VL trans. I recently put new sealed bearings in my transmission and also replaced the clutch plates but I'm having a hard time shifting in to first or second from an idle. Once the bike is moving the rest of the up/down shifting is fine. When at an idle though, trying to get into first requires a lot of moving the bike back and forth and double clutching to finally get it to go without grinding. I notice that even after adjusting the clutch that the bike is still noticeably harder to push when the clutch has been released than when the bike is in neutral and the clutch engaged. From reading this post I'm thinking my thrust washer is too thick and causing some additional drag?

    Leave a comment:


  • Peter Cooke
    replied
    Thanks Ray,
    Very much appreciated.

    Leave a comment:


  • 34VLRay
    replied
    970D4E2F-B38D-4D25-BBB2-4977F88012B8.jpgtook me a while to figure out how to make this work
    Bottom left and right are homade stamps. On retainer is stamped washer. I just finished another VL Tranny today,same issues. Hope this helps. Ray

    Leave a comment:


  • Peter Cooke
    replied
    Right, got it now thanks. My g'box came in pieces so I never had the original bearing to compare to the sealed one. I went back and looked at Grumpa's photo in post #50 and you can sorta see how the inner sits off centre to the outer.

    I'd be interested in the details of your new washer if your able to share it? I'm sure others would as well.

    Leave a comment:


  • 34VLRay
    replied
    It’s not the width that’s different. The original bearing race is not centered,there is some offset If you measure from inner race to outside face of threaded retainer on original vrs installed 6304 bearing you will see the difference

    Leave a comment:


  • Steve Slocombe
    replied
    Dear All, don't forget that sealed bearings moves the gearbox mainshaft relative to the clutch, so you will probably need a new 2500-19 thrust washer under the clutch hub bearing. Harley made this in 0.006" size increments so must have thought it important. Too thin allows for wobbly clutch, two thick binds the clutch drum and drags the clutch after rebuild, which is even more annoying.

    Leave a comment:

Working...