VL Trans rebuild

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Peter Cooke
    replied
    "When you install sealed bearings on the kicker side the inner bearing race is outboard about.060 more that’s why I make changes."

    I'm curious to know how that happens if you're using a 6304 bearing? As Grumpa states in post #50 there's only 5 to 6 thou difference in the width of old vs new.

    Not in any way suggesting you're wrong. Just trying to learn.

    Leave a comment:


  • 34VLRay
    replied
    60 thousand. Enough to move washer away from bearing retainer

    Leave a comment:


  • Peter Cooke
    replied
    "..I make a new washer to hold spring and doesn't touch bearing like original one."
    Any chance you could share the details?

    "...is outboard about.060 more..."
    I'm assuming you meant 6 thou?

    Leave a comment:


  • 34VLRay
    replied
    I have noticed slight wAsher rub on originals
    When you install sealed bearings on the kicker side the inner bearing race is outboard about.060 more that’s why I make changes. That washer would be constantly rubbing.

    Leave a comment:


  • Peter Cooke
    replied
    Wouldn't that have been happening anyway? My 2288-17 shows a slight rub ring where the original inner bearing race would've contacted it. I guess the biggest difference now is there is no lube leaking to those area's.

    Leave a comment:


  • 34VLRay
    replied
    Enjoyed reading your trans rebuilding, I rebuild them also not quite as thoroughly as you. The only thing I’ve noticed is when using the sealed bearings the 2288-17 bearing washer on drive side has slight contact with bearing race so I open up washer so it’s larger , also the stepped washer 2151-31 now rides on bearing race on shaft this may cause washer and spring to turn ,I make a new washer to hold spring and dosent touch bearing like original one. Ray

    Leave a comment:


  • Guest
    Guest replied
    Those pictures look like crap. Why did they get blurry when a posted them?

    Leave a comment:


  • Guest
    Guest replied
    Grumpa I finally got it done. It took me a while to catch up with you. Still have a long wait before I can test it out but this part is done. Thanks again. I’ll show you a picture if I can figure this out.
    Attached Files

    Leave a comment:


  • 26fhead
    replied
    Gumpa,

    That's odd as my new springs that I bought from Easy Russ several years ago measure 1.60+ and my old springs are 1.50+or - so I thought the new springs might be too tall.

    Thanks again for all your help as I am building a parts bike.

    Steve

    Leave a comment:


  • Grumpa
    replied
    No problem at all Steve, I have some loose springs.

    All the old ones average to 1.60+ whereas the new springs are 1.55+ oddly enough. It seems to me there are some design weak points but those springs aren't one of them.

    Leave a comment:


  • 26fhead
    replied
    Grumpa,

    If you still have that clutch apart can you tell me the height or overall lenght of the springs? Don't bother taking it back apart because I don't want to be a pain.
    Thanks again for all the pictures and your time!!!!!!!!!!!

    Steve

    Leave a comment:


  • Grumpa
    replied
    Not that it isn't possible to put the spring on the post: Bad VL clutch springs.jpg some of the springs may fit. But if you flip the assembly over you can see how you want the spring sector under the 2505-30 clutch actuating plate leg: IMG_2416_LI.jpg

    Leave a comment:


  • 26fhead
    replied
    Grumpa,

    Thank You very much the pictures help, also thanks for taking the time to post them.

    Steve

    Leave a comment:


  • Steve Slocombe
    replied
    Yup, that's it, you don't want to have a clutch spring over one of those three posts sticking out from the drive disc.

    Leave a comment:


  • Grumpa
    replied
    Originally posted by 26fhead View Post
    What is the correct way to assemble the clutch?
    26fhead,
    I'm taking the liberty to post these pictures which might help The outboard looking in IMG_2413.jpg The side IMG_2414.jpg Inboard looking out IMG_2415.jpg and the hardware order IMG_2417.jpg. If pictures of anything else would help, let me know.

    Leave a comment:

Working...