VL Trans rebuild

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Robert Luland
    replied
    Anyone have a straight mainshaft available?

    Our custom work is designed from scratch. We offer manufacturing of OEM parts for a number of different classic bikes including Harley J, JD, UL, VL, Knucklehead, Panhead, Shovelhead, EVO, HD, Sportster, Springer, and that's JUST the Harleys. We also offer custom work designed and manufactured specifically for your customization or restoration needs.

    Leave a comment:


  • Grumpa
    replied
    Originally posted by dustydog View Post
    I think you should run it as is Grumpa.
    Yeah, believe me I thought long and hard about just letting it go. In the end though it's not like I need it in the bike tomorrow morning to get to work so I opted to check it out. I tore it back down. Tranny blood, guts and oil everywhere mainshaft out last night. Checked it out today between centers and found the shaft to be straight (at the most out a half thou). The variables are the case (not likely) the large bearing, the main drive gear, and the internal main drive gear bushing. I did note on assembly that there was a clearance fit between the gear and the bearing and consequently I mounted the gear with red Loc tight. That might be the where the offset happened. So I checked the main drive gear IMG_2321.jpgIMG_2320.jpg and found that was where the .006" runout came from.

    My plan is to replace the bearing (to eliminate that variable) and re-center the gear in it with Loc tight in the case vertically instead of horizontally and then re-assemble. If it's still way off after that I'll take a closer look at the clutch hub/shell. Opinions are most welcome at this point.

    Leave a comment:


  • Guest
    Guest replied
    I think you should run it as is Grumpa.

    Leave a comment:


  • Grumpa
    replied
    I indexed the hub 180 degrees from the previous installation just in case the hub bore wasn't perpendicular to the flange and then re-riveted with the above described repair IMG_2311.jpg no gaps at any of the rivets now. Reinstalled on the shaft and run out is now down to +/- .028" (.056" total runout) and it's at the same place relative to the shaft as before IMG_2316.jpg so that pretty much eliminates everything but the mainshaft which was out .006". Anyone have a straight mainshaft available?

    Leave a comment:


  • Grumpa
    replied
    Well I found at least part of my problem; even with set-up hardware drawn up tight I still have a .002" gap IMG_2310.jpg which means the ID of the shell has a smaller radius than the hub, easy fix. But when I riveted it before that gap allowed the rivet shank to expand it even further like the proverbial salesman getting his foot in the door. That makes me feel a bit better.

    Also now that this assembly has been riveted at least three times that I know of (once by the factory and twice by yours truly) the holes are oversized. I'm trimming down some ACRES Sleeves IMG_2308.jpg to 5/16" to help with that IMG_2309.jpg and make a repair bushing that should also help keep the shank where it should be. The rivets are 0319s brazier heads cut down to 5/8".
    Last edited by Grumpa; 11-12-2018, 09:46 AM. Reason: corrected sleeve length & added rivet type

    Leave a comment:


  • Grumpa
    replied
    So two separate problems; the mainshaft is one issue and the hub is another. I did a better set up to check the mainshaft and confirmed a .006" runout IMG_2304.jpgIMG_2305.jpg. I have a repair plan for the hub and I can obviously R&R the mainshaft again if I have to. Is .006" runout too much?

    Leave a comment:


  • Grumpa
    replied
    Well crap, I re-riveted the hub and still have a gap of .004" which is better but obviously not great. More importantly on assembly there was still an .080" runout at the clutch shell. For yucks I did a quick and dirty check on the shaft and it looks like it has a .006" runout: IMG_2302.jpgIMG_2303.jpg. I'll take the hub and shell apart again (practice makes perfect) but if the shaft is off that isn't going to fix it. Pretty sure it would function like this but dang I don't like it. Any advice from the elders here would be much appreciated.

    Leave a comment:


  • Grumpa
    replied
    Let me ask my question another way, what's the difference between a JD mainshaft diameter at the clutch and a VL mainshaft? The reason I'm asking is that it looks like someone is making the 2494-19 hub but I haven't seen anyone make the 2494-30. Obviously the parts are different, I just don't know how.

    Leave a comment:


  • Grumpa
    replied
    I will say this, I noticed on removal that the hub cracked at more than one place. I gotta say I'm not real worried about it primarily because that the OEM original design had short edge distance. There is a reason why you design for a 1.5 times the diameter of the rivet edge distance as a minimum. These cracks aren't going anywhere, they end at the rivet hole. I could re-use this hub, but here's my question; what's the difference between a 2494-19 hub (1919-1929) and a 2494-30 hub (1930-1936) dimensionally?

    Leave a comment:


  • Guest
    Guest replied
    I see what you mean now. When you said hub I thought you were taking about the drive portion of the clutch on the tapered end of the shaft. You’ll be a good riveter when your done but probably not as pretty as Rosie.

    Leave a comment:


  • Grumpa
    replied
    Originally posted by dustydog View Post
    It looks like you have the dial indicator on the clutch shell Grumpa. That shouldn’t be effected by the hub.
    I checked the clutch shell on a surface plate IMG_2291.jpg and couldn't get a .001" feeler gauge under it, but I got a .008" gauge between the hub and the shell IMG_2290.jpg so I'm fairly confident that's the problem. Granted the mainshaft could be bent and I failed to check it prior to installation; possible but not probable. So hub removal reveals rivet material that spread out between the surfacesIMG_2292.jpg. I knew to have the pieces drawn up tight together but I failed to do it, and THEN I didn't check for a gap. Bottom line is I messed up, don't let this happen to you dear fellow AMCA member who reads this thread.
    Last edited by Grumpa; 11-09-2018, 05:47 PM. Reason: added pic

    Leave a comment:


  • Guest
    Guest replied
    It looks like you have the dial indicator on the clutch shell Grumpa. That shouldn’t be effected by the hub.

    Leave a comment:


  • Grumpa
    replied
    75'# it is IMG_2275.jpg Sadly when I put on the clutch I found a .080" runout that I didn't spot earlier. IMG_2288.jpg almost certainly because I didn't have the hub drawn up tight when I was riveting it on. The only other possibility would be a bent mainshaft which isn't likely because it's new. All I can say is I am very thankful for Mark Masa's clutch removal tool IMG_2289.jpg
    Last edited by Grumpa; 11-08-2018, 07:04 PM. Reason: eliminated duplicate pic

    Leave a comment:


  • Steve Slocombe
    replied
    Wow Grumpa, that is tight. There are no surviving torque specs for the VL, and maybe none were ever issued. Crank pin nuts had to be done up 'very tight' but a lot seems to have been left to the experience of the mechanic. On the VL left hand sprocket lock nut, I clamp the sprocket in the vice, do up the nut tightly with a big adjustable wrench, finish off with a hammer and punch, then turn over a lock tab. No idea what this would be on a torque wrench, but so far so good after 74 transmissions.

    Leave a comment:


  • Guest
    Guest replied
    That seems awfully high to me. I would think 75 foot pounds would be plenty.

    Leave a comment:

Working...