Knuckle Heads

NOTICE: New member email requirements now in effect. Longtime member having trouble logging in? Please review the requirements here.

Only registered users may post new messages on this forum. You must be an AMCA member to register. Click the register link on the top right to proceed.

If this is your first visit, be sure to check out the FAQ by clicking the link above. To start viewing messages, select the forum that you want to visit from the selection below.
If you are NOT an AMCA Member and would like to join Click Here

AMCA Community Forum To Receive Upgrade

Please be aware that Saturday July 5, 2025, the AMCA will be completing an upgrade to the AMCA Community Forum. This upgrade will at times make the Community Forum unavailable. We are sorry for any inconvenience this will cause members. Thank you for your patience.

See less

Topics	Statistics	Last Post
Long vs. Short rib cases by Americanrider Started by Americanrider, 06-16-2010, 11:44 AM	15 responses 187 views 0 likes	Last Post by SteveBarber 01-01-2011, 11:18 PM
47 Knuck engine finishes by tomcat1 Started by tomcat1, 11-24-2010, 07:02 AM	23 responses 10,317 views 0 likes	Last Post by Chris Haynes 01-01-2011, 08:10 PM
Installing valve guided Knucklehead by DANPATCH Started by DANPATCH, 12-30-2010, 03:37 PM	6 responses 2,745 views 0 likes	Last Post by junkyarddog 12-31-2010, 04:11 PM
Installing valve guided Knucklehead by DANPATCH Started by DANPATCH, 12-30-2010, 02:55 PM	2 responses 1,716 views 0 likes	Last Post by DANPATCH 12-30-2010, 11:26 PM
Truing flywheels by DANPATCH Started by DANPATCH, 12-29-2010, 10:53 AM	4 responses 6,888 views 0 likes	Last Post by DANPATCH 12-30-2010, 01:06 PM
Wiring diagram 46 EL? by sirhrmechanic Started by sirhrmechanic, 12-28-2010, 09:48 PM	1 response 1,431 views 0 likes	Last Post by Sargehere 12-29-2010, 02:00 AM
Oil Lines for 1946 EL Steel? Copper? by sirhrmechanic Started by sirhrmechanic, 12-22-2010, 04:29 PM	17 responses 5,488 views 0 likes	Last Post by Lonnie 12-27-2010, 01:01 PM
Speedometer ID and recommendation for rebuilder? by sirhrmechanic Started by sirhrmechanic, 12-25-2010, 03:17 PM	5 responses 2,676 views 0 likes	Last Post by Chris Haynes 12-26-2010, 10:45 AM
Flywheel shafts sprocket and pinion. by DANPATCH Started by DANPATCH, 12-25-2010, 04:46 PM	1 response 1,425 views 0 likes	Last Post by billpedalino 12-25-2010, 06:12 PM
Judging manual by DANPATCH Started by DANPATCH, 12-15-2010, 01:40 PM	13 responses 4,208 views 0 likes	Last Post by billpedalino 12-25-2010, 07:56 AM

Previous 1 50 90 97 98 99 100 101 102 103 110 137 template Next

No topics found.

Mark This Channel Read

NOTICE: New member email requirements now in effect. Longtime member having trouble logging in? Please review the requirements here.

Announcement

AMCA Community Forum To Receive Upgrade