101 Scout... going to take a while

[pisten-bully]

I got a bit of interesting information on my front wheel hub this morning (thanks to the sharp eyes of Dave on the Caimag site), until he mentioned the dished flange away from the brake side, I had never paid attention. Brake drum, spoke count, and rim size all looked good.... but this is not the correct hub! I measured it up and it's way wrong.... sheesh. So now I need to figure out what it is and where to get the correct hub. Makes sense that it's not the right one, the rear wheel that came with it turned out to be Henderson. One step forward and two steps back....at least I hadn't painted it and laced it up to the new rim!

[Tom Lovejoy]

Tom, mines a Chout build and far from stock - 1930 frame 101 and highly modified 47 Chief engine. With cylinders that were shortened almost 2 inches, so that it would go into a stock 101 frame - that's why I had to cut the trans tower, also my trans is one of the new 4 speed overdrives :-)

[pisten-bully]

Mike, this is what was in there. I'm not certain if it's correct, and if so if it should be nickel or painted.... another detail to learn down the road!

[ihrescue]

Very nice looking seat and the reworking of the parts. On the front springy tongue portions of the seat mount what holds the pin in the frame bracket. Or is that a bolt. Can't see that detail.

Mike Love

[pisten-bully]

I also built an engine stand. I wanted a stand that can accommodate engine alone and also with the gearbox bolted up, so I made the base leg long and made two different vertical mounting brackets. To use the stand with the gearbox attached I'll remove the front mount for engine only and add the rear mount to hold the gearbox mounting point once they're bolted together.

[pisten-bully]

The 101 came only with a front wheel and hub, well not exactly... the rear hub and wheel were Henderson so I traded that assembly for the correct Indian hub. I purchased a new drop center rim and proceeded to unlace the clincher from the front hub and drum. It actually went very well, I simply applied a few drops of Kroil to each nipple from the inside and was able to get them off without too much trouble. My plan, unless I get talked out of it, is to use the original spokes and nipples on the new rim... as long as there's enough thread on the spokes because the drop center nipple holes are a shorter distance to the hub than the original.



BTW, the original clincher has some markings inside (and I don't need this rim, hate to toss it so if you have a need for one then let me know!)

[tfburke3]

Hey Tom,I am curious why you would shorten the trans tower.I am not to familiar with 101's,more chiefs.
I ask because I have a tower similar to chief but shorter,which I thought was later scout but may be other.
Tom

[exeric]

Thanks for the pictures, and text, Harry. What you're doing is my favorite part of messing with old motorcycles. I hope you're having fun.

[Tom Lovejoy]

Very cool, I just replaced the tubes in my handlebars. Just cut and shortend my trans tower 1 1/8th inch and I am going to have to make a new shaft like the one your showing, that the shiftter attaches too. Keep at it and keep the updates coming.

[pisten-bully]

What was the cost to recover the seat? Thanks Mike

Without looking it up I'd say it was right around $300. Don't tell my wife, please! We have an understanding....she doesn't ask and I don't tell (unless it shows up from Ebay and it was inexpensive!)

[banjomike]

What was the cost to recover the seat? Thanks Mike

[pisten-bully]

The gearbox was my next stop, I opened it up to find the slider gear pretty well past its prime



I tracked down a new gear and added that to my stash for when I rebuild it. Up top I had a left hand shifting tower, and I mistakenly thought all would have to do is reverse the tower and voila! But the actuating arm is offset so it's not that simple. The arm is riveted to the shaft that the shifter attaches to, so I carefully ground off the mushroomed end of the rivet and tapped it out. Greer's sells replacement rivets for later Scout gearboxes and they happen to be the same size...that was an easy find!

[pisten-bully]

Next up was the RH handlebar, a messy sausage looking thing so I decided to replace the right side only



Cut off the old bar and had a friend mill out the casting so that new tubing could be installed, and since he was so helpful he cut the slot for the cable puller. We decided to simply match the rise of the new bar to the LH side, even though the 101 R&O manual tells of a different rise!

[pisten-bully]

I went for completion on one item to show myself some progress! The saddle was pretty much an incomplete skeleton so I worked on that first (last year...)

The pan was in trouble, some cracks and blown out holes:



So I did some welding up of the holes and cracks, and fabricated a missing threaded insert for an optional Mesinger back rest (which I don't have)



I also needed a few parts (there's a bunch of parts in one of these seats!), but the few missing parts were available through Walker



...and sent the seat off to Michael Paquette of Worsham Castle... I am quite pleased with the results, thanks Michael!

[Tom Lovejoy]

Looking forward to your up dates