The making of a 1936 Knucklehead springer front end

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Jerry Wieland
    replied
    Originally posted by MMasa View Post
    We're these legs originally roll forged?
    Mark
    Mark I do not know what you mean by 'roll forged' but I am absolutely convinced that the legs started out with the profile of the up tubes. They then went inside with a "swedging' tool and spin expanded the leg until it looked like a lamp post. When this was done it was put into a stamping fixture and "flattened' and given the offset bend. I think that the swedging had a tool hardening effect on the leg and added to the strength of it as a result. The 'porkchop" piece as I have heard it called added even more strength where it was needed most.

    This process was a fairly common technique in the brass lamp industry that abounded in the 1920's and 30's and I think HD used it to make their frontends.

    I might be wrong but that is my story and I am sticking to it.

    Jerry

    Leave a comment:


  • MMasa
    replied
    We're these legs originally roll forged?
    Mark

    Leave a comment:


  • Steve Little
    replied
    Originally posted by Jerry Wieland View Post
    Robbie This is the first that I had heard of the dimples and I do not know what to make of it. I have no doubt they are original but the springer on my original 36EL2025 does not have them or do any of the other 4 early springers that I own. Secondly the obvious question is why. What is the reason for them. I cannot believe that a messed up stamping die would be allowed to run that long with such an obvious defect. Why only on one leg - I assume that both legs would have been stamped in the same die. Especially on a bike that they (HD) were apprehensive about releasing in the first place.


    Jerry
    Hi Jerry
    I am enjoying you'r picture sequence of work.

    A possible scenario for the dented leg. As follows:
    The forward sweep of the 1936-1940 springer legs, would mean that there would have been separate forge plate sets for left and right sides.

    Traditionally, *forge plates (when first manufactured), are hand polished with fine emery paper in the indented shape, to the smoothest possible finish.*

    A dent in one of the legs would mean that something has stuck to the surface of the indented shape of one of the die sets.*
    A possible scenario could be that the forge operators let the plates get too hot during production of the legs, and some red hot scale has annealed itself to the surface of one of the die sets.*
    If this happened part way through the production of the run, it would account for some having the dent, and some not.
    Supposition only!!*
    Regards Steve

    Leave a comment:


  • koanes
    replied
    I looked at the two 36-E37 forks I have and they both have the dents, obviously part of the manufacturing process. One of them came with a motorless 37 basket case I bought, the other with a parts pile, so no history. Jerry, I think you better push some dents in the fork to finish the job. (Insert face with smile)

    Leave a comment:


  • Jerry Wieland
    replied
    Originally posted by Chris Haynes View Post
    Use a Rosebud tip for best results when brazing.
    Thanks for the advice Chris

    Leave a comment:


  • Chris Haynes
    replied
    Use a Rosebud tip for best results when brazing.

    Leave a comment:


  • duffeycycles
    replied
    Jerry ,on both my Cannon and my Nikon,Macro[close up] is a flower..on Nikon SLR it's on the dial on top of camera,
    on point and shoot cannon its on the back
    Flash on off is a lighting bolt..same thing,on top SLR -on back on point and shoot
    On SLR you rotate to the lightning bolt ,on point and shoot you press it and it will say flash on ,press again it will say flash off,,,wait until it's done before chainging to Macro or it will turn the flash back on
    hope this helps .Roger

    Leave a comment:


  • Jerry Wieland
    replied
    I also needed to slim down the fender tabs so I made a patter from another front end,



    I then laid it on the springer fender tab and carefully outlined it with a marker and started carefully removing metal until I was happy with result.





    Leave a comment:


  • Jerry Wieland
    replied
    The brake anchor needs to have the weld disappear and be brazed. I have not had much luck trying to braze with a torch what HD brazed with a furnace. It is hard to get enough heat into the fork to get the braze to fuse without getting too much heat. So what I do is dress the weld until it no longer looks like a weld. I have had a fair amount of practice doing this because over the years I have fixed quite a few Indian frames that had 'slipped joints'. The late Indian frames were very poorly brazed and it is not uncommon to have a joint pull apart. I would remove the tube and then because I no luck with brazing the big bulky Indian castings, I would weld them and then have to dress them back to appear not welded.

    Before



    After

    Leave a comment:


  • Jerry Wieland
    replied
    Originally posted by duffeycycles View Post
    Love this thread Jerry..If I am using a digital camera..I have found that turning off the flash and using one or 2 led flashlights [or droplight] to highlite the area...and changing to Macro on closeups gives the desired clear shot..hope this helps
    The problem I have Duffey is that I have lost the instructions for my camera and have forgotten what a lot of the setting do. I really need to get another manual for it.

    Jerry

    Leave a comment:


  • duffeycycles
    replied
    Love this thread Jerry..If I am using a digital camera..I have found that turning off the flash and using one or 2 led flashlights [or droplight] to highlite the area...and changing to Macro on closeups gives the desired clear shot..hope this helps

    Leave a comment:


  • 36 knuck man
    replied
    Great interesting thread Jerry. As for the mystery dents I also have seen these on some 36 forks but have also noticed it is not on a lot of them. Of the 17 36,s I have owned a couple of them had the dents but most did not. The all green bike in Louisville which is 100% factory stock does not have them. Keep the comments coming, I love this thread.

    Leave a comment:


  • Jerry Wieland
    replied
    Robbie This is the first that I had heard of the dimples and I do not know what to make of it. I have no doubt they are original but the springer on my original 36EL2025 does not have them or do any of the other 4 early springers that I own. Secondly the obvious question is why. What is the reason for them. I cannot believe that a messed up stamping die would be allowed to run that long with such an obvious defect. Why only on one leg - I assume that both legs would have been stamped in the same die. Especially on a bike that they (HD) were apprehensive about releasing in the first place.

    Jerry

    Originally posted by Rubone View Post
    That extended '36 fork I posted on the first page has the dimples in it.

    Jerry that fork is looking good!
    Last edited by Jerry Wieland; 12-28-2013, 09:52 AM.

    Leave a comment:


  • Rubone
    replied
    That extended '36 fork I posted on the first page has the dimples in it.

    Jerry that fork is looking good!

    Leave a comment:


  • Jerry Wieland
    replied
    Now I have to drill and tap the holes for the inboard zerks. The thread is 5/16" x 32 tpi. I drill these by hand being very careful that the small pilot hole hits the grease groove on the inside. The tap is one I special ordered and is the standard for most HD grease zerks that I am aware of. I drill the final hole and control the depth of it by merely putting a round of masking tap on the bit at the depth I need.

    Poor photos I know but it is all I have for now.



    Leave a comment:

Working...