Jules’ favorite bike 1928 101 Scout

[FLFD7]

Dave and Eric,
The clutch hub tool is handy, I’ve used it on 3 Sport Scouts and this 101. The hub part is some sort of plastic, I don’t know what the material is, maybe Delrin? The handle is just flat stock and there are 2 thread inserts pushed into the plastic. It looks to be easy enough to make, but I actually bought this at a meet years ago, I think at the time it was like $20 or so. I mean, between time and material I couldn’t make it for that, so done deal.

[FLFD7]

It’s been a busy 3 weeks or so, getting stuff ready for Oley and selling my Indian 4 I had my hands full, so now back on the 101. At Oley I did pick up my refurbished magneto…

IMG_3157.jpeg

So that’ll be ready when the time comes.

Next up I’ll start with something easy, the transmission cover.

IMG_3156.jpeg

Got everything apart now to clean and reassemble…

[Green Indian]

The Magneto looks great who rebuilt it for you?

[FLFD7]

This guy…

IMG_3168.jpeg

[FLFD7]

Well, nothings easy. I started going thru the trans tower and didn’t like what I found…

IMG_3174.jpeg

Got a bit of wear here…

IMG_3175.jpeg

And the casting is cracked, likely cause the cap was loose and the shifter shaft was wobbling back and forth winds up bell mouthing the journals

IMG_3176.jpeg

And messing up the bushing

IMG_3178.jpeg

Lucky for me I have more parts in the stash and I’ll need a different tower, cap and end bushing.

[FLFD7]

Here are some pictures of the new assembly after it was cleaned up…

IMG_3180.jpeg IMG_3181.jpeg

Much better, nice and snug.

Ready for assembly

IMG_3182.jpeg

And back together

IMG_3184.jpeg IMG_3185.jpeg

For you purists out there yes, the cap should be held on with threaded studs and nuts and I used hex head screws. First off the correct studs use 1/4-24 nuts, and I don’t have too many of those obsolete sized nuts, and I have plenty of 1/4-20 screws. I get it that studs and nuts are better if that part is going to be assembled and disassembled a lot, which I don’t see the cap for the shifter shaft being removed too often. Besides, later Chiefs used screws on the cap so I figured that’ll be fine, it’s not going to be judged or anything. I will use studs and nuts to mount the tower to the trans case, even then I bought new studs 1/4-20 in the case and 1/4-28 for the nuts.

Next up the primary drive…

[pisten-bully]

That looks great Joe! Nice to have a few parts laying around, too. And it's also encouraging to see that Greers is gradually adding to their selection of 101 parts and that they're now able to supply those 1/4-20/1/4-24 studs for the cover.

[FLFD7]

Primary time…..

IMG_3206.jpeg IMG_3205.jpeg

They needing a good cleaning, obviously…

IMG_3213.jpeg

Inner pretty much done. While cleaning I noticed…

IMG_3214.jpeg IMG_3215.jpeg

It’s been welded on….but looks fine I think.

Next up cleaning the outer…

[FLFD7]

Well, not so fast. I’ve been pondering this inner primary and I’m not thrilled with the welded area after all. The mating surface still shows a crack

IMG_3245.jpeg

Jules used Permatex on the covers, I got a new gasket and I suppose I could JB Weld over the crack and smooth it out to hopefully prevent any leak, but I have other inners so maybe I should use one.

I was also thinking what caused the break there that needed to be welded, and I think I figured it out. There isn’t much clearance between the cross over lever and the primary case…

IMG_3217.jpeg IMG_3218.jpeg

These are pictures of a 101 racer Jules built. You can see the “modification “ made to the case to accommodate the head of the screw on the lever. Other inner primaries that I have show a similar “modification “

IMG_3219.jpeg

Here is one (top) compared to my cleaned up one (bottom)

IMG_3220.jpeg

And here is another.

I need to do more investigating, but I’m learning toward using a different inner.