Fixture

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Steve Little
    replied
    Thanks Harleytoprock and Bob.
    The synchronicity was sweet. I literally got off the phone from the secondhand machinery house and went straight to eBay. Dialogue with eBay seller below: Start at bottom and read upwards.



    New message: yes bring the money over today ...


    eBay
    New message from: hopeless99 (191Turquoise Star)

    yes bring the money over today

    jack
    Reply
    Your previous message

    Will you take three hundred. I would bring cash and pick it up today.
    Regards Steve

    WALDOWN TOOLPOST GRINDER
    Current bid: AU $350.00
    Auction ends 13 Dec, 2016 07:01 AEDST
    Bids: 0
    Place bid
    Get to know the seller hopeless99

    • Located: MELBOURNE, Victoria, Australia
    • Member since: 26 Apr, 2005
    • Positive Feedback: 100%

    Leave a comment:


  • BigLakeBob
    replied
    Steve, I think that is a great unit, especially for the money. Boy, timing is everything, jump on ebay and 30 min away. The only thing I might do is tighten the gib on the cross slide if you have some play now, and maybe even use the carriage lock a little, you can always loosen it up when you go back to turning. I would also relieve half the wheel width, when dressing (on the right side of the wheel- furthest from the work shoulder) dress it maybe .010 smaller so you are only using half the wheel. Then when grinding I always start on the shoulder side, (left in your case) and feed right, this helps prevent corner wheel break down. So go to the shoulder, feed in, grind right, back off of work piece and repeat. As we all know in machining there are many ways to skin the cat, but this method works for me. Also, a .0001 or .0005 reading travel dial indicator on a mag base may help control the in feed amounts and help when you back off to start the next cut if you choose to use my method. (Note: if there isn't a shoulder then I would grind left and right and not back away each time, you can grind these pieces without backing away, just when you get close to finishing you may have more of a radius at the shoulder.) Great buy! Have fun.

    Leave a comment:


  • harleytoprock
    replied
    Nice grinder! Make a fixture to hold the diamond dresser in a locked spindle, 3 jaw chuck. Make sure the diamond point contact with stone is below center ( really depends on stone rotation direction). True stone each time grinder is installed on lathe to insure stone is square with work. Protect ways from grit. Experiment with feed rates. Light cuts!

    Leave a comment:


  • Steve Little
    replied
    Bob if you mean centering the spindle to my lathe, it has adjustment for that.









    Do I have everything?

    Leave a comment:


  • Steve Little
    replied
    I rang the machinery house. Unfortunately the 240 volt unit was sold. I must have got the price mixed with another item I asked about. He said it sold for AU$900.
    I went straight to my other friend, ebay.com.au and found a similar size 3 phase unit for $350 just 30 mins from my place. It lacks a belt guard and is not as pretty so I offered $300 cash and pickup within the hour. Being Christmas, he was onto the cash deal in a flash. I went from his place to a great store that sells toolroom equipment and bought a range of roughing, medium, and finishing stones to suit hard chrome.



    I have a length of 3 phase lead but not sure if I have a plug.
    For $300 and the limited work I will do with it, I think I'm safe to feel happy with it....unless one of you killjoys tells me its too big or too powerful
    The stones were $30 each and the 2 new belts $15 each.
    Thoughts? Some helpful hints on how to use it.

    Leave a comment:


  • BigLakeBob
    replied
    You don't need that much grunt! But if price is right and the c/l of it and your lathe line up, bigger is better sometimes. Make sure the c/ls are compatible. Here is a picture of mine that is a good size for a 12"-15" lathe. I think it holds up to a 3" wheel for OD grinding.

    Leave a comment:


  • exeric
    replied
    That seems like overkill for a tool post grinder. I've always thought patience, and light passes were the key to accurate, and successful grinding. However, I do remember machinists that believed deep cuts, at maximum feeds were the hallmarks of efficiency Having said all that, Steve; that looks like a very nice tool post grinder, and one I'd like to own.

    Leave a comment:


  • Steve Little
    replied
    It is only 240 volt. I have found one that is same size but 3 phase 440 volt. How much grunt do I need?

    Leave a comment:


  • BigLakeBob
    replied
    Originally posted by 38 el View Post
    I just turned the shaft true, and it cleaned up at about .736 or so. Then made an undersize bushing to match.....
    I did the same thing for mine, you just can't go too small because the gear needs a surface to seat against. Then I (purists close your eyes) counterbore the cover to accept a lip seal (the washer hides it all) and gang the bushings together or make a one piece longer bushing. I figured this way oil gets to both bushings and dirt doesn't enter and destroy the end that always wears the most. A problem I also encountered was the square that locates the gear was worn from use and probably a loose nut. I had a few welded but haven't got around to remachining the square yet.

    Leave a comment:


  • harleytoprock
    replied
    Hi Steve, I've used this company in California to save some parts for me.
    Electronic Chrome and Grinding has very deep hard chrome plating tanks for commercial hard chrome applications: oil and gas drill rotors, racing crankshafts, motorcycle forks. Call 562-946-6671. We also provide ID - OD Centerless grinding services.

    My lathe tool post grinder pales compared to the massive grinding equipment they have. They can undercut the shaft, hard chrome with masking and then grind to your size specs. The only problem for you would be the shipping expense. Maybe you can find a similar company by you. Good Luck! HTR

    Leave a comment:


  • 38 el
    replied
    I just turned the shaft true, and it cleaned up at about .736 or so. Then made an undersize bushing to match.....

    Leave a comment:


  • Steve Little
    replied
    Hi Bob.
    I'm with you on that.
    After posting here today, I set the lathe up and had an experiment with the hone on the hard chrome. I only have mild steel stones and after 20 minutes of honing I had nicely polished the shaft but had only removed 001".
    I then rang Sunnon and got their advice on stones and guides. The quote on two sets of diamond stones and hardened guides for the job would run close to AU$800.

    When harleytoprock suggested a tool post grinder, the idea starting looping through my head. Damn it toprock. Be careful where you point those loaded ideas 
    There is a second hand machinery dealer that I like to drop into sometimes.
    But I try to keep my visits short. For some reason I can turn into a impulse shopper while I'm in there.
    After I dropped the cranks at the hard chromer a while back, I was driving home and was due to go past the road to the machinery house. No!...I haven't got time. No really. I haven't got any money......on went the blinker and in I went.
    They had a really nice pre loved (mid size) Waldon tool post grinder for $600.
    I didn't buy it at the time...thinking I was doing so well. But I did take a picture with my phone. I will upload the picture to Photobucket tomorrow and post it here.

    Considering the cost of the diamond stones and guides for the hone, I could buy the grinder and be in front. I haven't used a tool post grinder before but my friend YouTube showed me most of what I needed know.
    I'll give them a call tomorrow and see if it is still there.

    The hone did a beautiful job of cleaning the original steel on the shafts but it is not the right tool for roughing 030" off a product like hard chrome.
    Thanks for your input Bob.
    Regards your humble apprentice Steve
    Last edited by Steve Little; 12-08-2016, 05:39 AM.

    Leave a comment:


  • BigLakeBob
    replied
    Steve, isn't honing that much going to take quite a while? Wouldn't OD grinding be better? I realize it would take a pretty large swing grinder, but honing .034 in hard chrome will be quite the task.

    Leave a comment:


  • Steve Little
    replied
    Hi.
    Haven't been in my workshop for a while but its blowing a gale today, so thought I might get in here try to finish off a couple of jobs.
    Kerry. Sorry for the late reply. I like lateral thinking and your idea may work out a lot cheaper than the route I have taken.





    These are the starter cranks I sent to be hard chromed. One is smooth as babies bum, the other has some micro pimpling in the chrome but the hone will take care of those.
    Before chroming, I cleaned the ruts and wear out of the shafts.
    After honing, one measured 0.733 and the other was about 0.738” After chroming, the .733” shaft is now .769” and the 738” shaft is now .784”. Both will be honed down to 0.750"
    Hard chrome for each shaft was AU$150. This is aside from the work I did on them. Both shafts still have to be honed down so some labour to put into them.

    A thought to ponder:
    Does a detailed, repair like this help to determine the going price of a worn out original unit?
    Or is there no common sense used in determining the price of vintage HD parts?
    Perhaps there is no logic... just pay what is on the sticker.

    One of these cranks had been chromed and I had it stripped a while back. The other crank was a nice original paint unit. But I notice they have blasted the paint off a portion of it. These were posted back to me so I didnt get to ask about why they need bare metal.

    Also thanks 1950Panhead for the Photobucket input.
    When I sold the business a couple of years ago, the web site and all email addresses connected to it went to the new owner. He contacted me recently to tell me that the web host in Melbourne was asking him if he wanted to renew for the next two years. He is moving the web site to a host in Japan so I helped him close the contract in Melbourne about 3 weeks ago. I didn't realise that my contact email for Photobucket was still steve@raceframe so it took a bit of wrangling but got it sorted and I'm back into Photobucket.

    Another question on Photobucket. When copying the link, do I click DIRECT or HTML?
    The reason I ask is when I followed the link from 1950Panhead I could see other pictures in my Photobucket file.
    I have been using Direct in previous posts.
    Regards Steve
    Last edited by Steve Little; 12-07-2016, 09:47 PM.

    Leave a comment:


  • 1950Panhead
    replied
    Any body else struck this problem since Photobucket did and overhaul some weeks back?
    Steve,
    My account is still working, your photos are still posted, try the "forgot" button to recover your id and pw.

    Leave a comment:

Working...