Fixture

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • exeric
    replied
    Beautiful work, Steve. I loved your comment about getting caught with your wife's tea towel. It reminded me of a welder I worked with; he soaked a cloth in water and was cooling down some dirty nasty thing he had finished welding. Suddenly a very angry fellow worker appeared and yelled, "That's my shirt, you ass****!" The welder replied, "Sorry, I thought it was a rag."

    Leave a comment:


  • painterdale
    replied
    I love this stuff! Keep it comin', Steve!
    Dale

    Leave a comment:


  • Steve Little
    replied
    Yep. I'm back at this again. Yell out if you've had enough of it.



    Centered the grinder spindle to the lathe. Then tightened up the gib on the grinder so that it was a little tight to move. Found a rag and wet it with water, and placed it over the ways.
    Turned on the fan and both machines and touched the grinder wheel to the job.
    Did a tentative cut at slowest feed rate to find out where the highs and low spots were.
    Found out that there was only a low spot near the shoulder and added 005” thou (aggressive..I know!!) and did my first roughing cut at “Fast” feed.



    At this point I found out why Bob was recommending to grind both ways. I cut up to the shoulder and turned off the carriage feed. Grabbed the hand crank and wound back the carriage to the start again but the result was sparks and a light, spiraling cut up the shaft.
    All following cuts were done, Feed in, Feed out.





    Roughed a few more cuts until I got to 0.755 and then crept up with a 004” at slowest feed and finished off with a 001'' finish cut. I probably should have left it for a couple of minutes before measuring the warm shaft but my last pass netted a tenth 0;0001” under 0.750”.
    I was pretty proud so when my wife brought in a drink I called her over to show off my work.
    She leans over and has a quick look and says (Yeah, that's good) Then she says,What are you doing to my tea towel. Ooops!

    For a backyard machinist I'm pretty happy with that.

    Leave a comment:


  • BigLakeBob
    replied
    Merry Christmas Steve, hope your recovery goes well. I look forward to more of your commentary next year.

    Leave a comment:


  • Steve Little
    replied
    Thanks for all the "Well wishes". Hope all the members, and casual readers have a merry Christmas and a safe and happy new year.

    Leave a comment:


  • bbinns
    replied
    Originally posted by Steve Little View Post
    Hi Ben.
    Good ingenuity from your dad. I plan to make the same holding fixture for my 4" grinder, fitted with a slitting blade. I need to grind a specialised shape on the end of a HSS turning tool.The slitting blade will give me the sharp corners in the profile I need.
    I first heard of Hard Chrome Engineering in about 1994, so I know they've been around for a while. They quoted $350 for chroming and grinding each of these shafts.
    I got them to do the chrome only, because I wanted to have a go with my external hone.
    There was a Big X for sale at the Bendigo swap a couple of years ago?
    It was on the back of a flatbed truck with another bike. Positive memory of the other bike escapes me, but it may have been an XA Harley. Did you buy the Big X?
    Regards Steve
    My Big X's have come from all over the place, but none from Bendigo swap. I must have missed that one!

    Thanks for the lead on Hard Chrome Engineering, I will check them out.

    Leave a comment:


  • Peter Cooke
    replied
    Originally posted by Steve Little View Post
    I'm having stem cell treatment tomorrow and have to stay off the leg for 4 to 6 weeks.
    Right in time for the Great Race Steve?

    I see your on the starters list. Good luck with the knee.

    Leave a comment:


  • 1950Panhead
    replied
    flailing and tumbling before a barbed wire fence kindly caught and nestled us for a while.
    During the ruckus, my left knee socket and ball had a disagreement and decided they were not in a relationship any more.
    Steve,
    Thanks for your help in the past and posting on the forum.
    I see you still have your humor.
    Do as the doctors say and best wishes for recovery.

    Jerry

    Leave a comment:


  • painterdale
    replied
    Best wishes to you, Steve!
    Dale

    Leave a comment:


  • larry
    replied
    Hondas are dangerous.

    Leave a comment:


  • Steve Little
    replied
    Hi Rooster. Thanks for your input and kind thoughts.
    By rights...I shouldn't be taking any kind thoughts. It was a stupid incident from my past that's come back to haunt me.
    40 years ago my first road bike was a K1 Hoona 4 with a 900 kit in it.
    Young, with little experience, I'd had a few beers at a game of footy and then rode to a party to meet up with a pretty sinorita. Didn't make the party, or the sinorita.
    A corner came out of the darkness and my speed didn't match it. I ran wide and the front wheel dug into a rut in the drain. The bike and I did some dainty, synchronised, somersaulting, followed by some un flattering flailing and tumbling before a barbed wire fence kindly caught and nestled us for a while.
    During the ruckus, my left knee socket and ball had a disagreement and decided they wern't in a relationship any more.
    Given time, they patched up their differences and joined up and all was good.....until the little bit of cartilage that was left, wore out a few years ago.

    I'm having stem cell treatment tomorrow and have to stay off the leg for 4 to 6 weeks. No weight at all on the knee. We don't want to crush the darling, newborn baby cartilage. The wonders of the modern world.

    Regards Steve

    Leave a comment:


  • Rooster
    replied
    Hello Steve,
    I've been quietly following along on this very interesting thread. Sorry to hear you are wheelchair bound; I hope you fully recover, and have a nice Christmas anyway!

    Leave a comment:


  • Steve Little
    replied
    Hi Ben.
    Good ingenuity from your dad. I plan to make the same holding fixture for my 4" grinder, fitted with a slitting blade. I need to grind a specialised shape on the end of a HSS turning tool.The slitting blade will give me the sharp corners in the profile I need.
    I first heard of Hard Chrome Engineering in about 1994, so I know they've been around for a while. They quoted $350 for chroming and grinding each of these shafts.
    I got them to do the chrome only, because I wanted to have a go with my external hone.
    There was a Big X for sale at the Bendigo swap a couple of years ago?
    It was on the back of a flatbed truck with another bike. Positive memory of the other bike escapes me, but it may have been an XA Harley. Did you buy the Big X?
    Regards Steve

    Leave a comment:


  • bbinns
    replied
    Hi Steve,
    Who are you using for hard chrome? I have a few Excelsior Big X kickers that I need to do and Im in Melbourne.

    I like your toolpost grinder, should come in handy for many things. When I was younger we needed to grind down the input and output shafts on an automotive gearbox to use in some home made agricultural equipment. Dad made a bracket for the 4" angle grinder (basically a piece of 20mm RHS with two band clamps around the grinder body) and fitted it into the lathe toolpost in the same way you would a cutting tool. Worked well for that purpose and surprisingly the angle grinder didn't fail with the side load! Not the accuracy of the real deal, but it cost nothing to make.
    Cheers Ben

    Leave a comment:


  • Steve Little
    replied
    Had a look at YouTube to see what was on offer. I came across an old apprentice training video for tool post grinding. Before watching the vid I was thinking coolant was involved. He was re-grinding a dead center in the head of the lathe. No coolant.

    Check if I got this right:
    The grinder will rotate (anti clockwise) down toward the swarf tray of the lathe (ways protected Toprock).
    Lathe chuck will run in reverse (clockwise) at low speed 39 or 64 rpm?

    Roughing stone: mid to fast feed rate. How many thou" can I take per cut?

    Mid stone cut and feed: mid to slow feed rate?. How much per cut?

    Fine stone: slow feed. How much cut per pass.

    Not sure if this electric motor is wired to be switched in direction, but if it can be, is there any benefit? Im thinking sparks down my neck would be attention grabbing, but not necessarily a benefit.

    Grinding and/or electrical motor knowledge would be greatly appreciated.

    A quick disclaimer: I won't be able to try any ideas that come out of this thread for a while. In fact...I won't be able to see over the top of my lathe for a while.
    As of Thursday, my mode of transport will be a wheel chair for the next 5 weeks.
    Wheel chair bound for Christmas and New Years. Ohh yeah! That was top of my Christmas list.

    Com'n AMCA members....Post interesting topics and many pictures to keep us invalids entertained.
    Steve.

    Leave a comment:

Working...