Fixture

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Steve Little
    replied
    Hi. I got the hard chromed shafts back and they look great. Thought I should finish this thread off. So I took some pictures and tried to send them to Photobucket so I could link them to the thread for all to see.
    I haven't used Photobucket since the last post on here, so it has been about 5 weeks. Put in the usual username and password, Bup bahh Incorect Username or password...Huh? I must have been day dreaming. Try again. Same result. Clicked the Forgot my username box and typed in the username.
    This Username is not registered with us. What?
    Any body else struck this problem since Photobucket did and overhaul some weeks back?
    It would be a shame if I have lost all my pictures.

    Leave a comment:


  • kg993
    replied
    Originally posted by Steve Little View Post
    I don't have a NOS, OEM, shaft to measure, so I used a new #33096-54B JIMS shaft to determine the correct size.
    The JIMS shaft measures 2 tenths shy of 0.750”
    I'm guessing the tolerance is probably +000” /-0005”

    I tried a couple of “James gaskets #33076-37” quad seals on the JIMS shaft and it has excellent surface tension.
    After fitting the “James” quad seals to a range of under sized shafts, I can report that they loose contact with a shaft at about 0.733”
    I don't have any OEM seals, so cant make an assessment if they still hold at 0.733”

    James Gasket quad seals, still have minimal surface tension at 0.738” but my guess is they may leak through capillary action.

    I plan to get a couple of the smallest shafts Hard Chromed, and I will hone them to 0.750.

    Future Steve, will report back then.

    Feel free to debate, discuss, or write a scathing rebuttal, to any, or all, that I have surmised.
    I am wondering when thinking about the lost quad seal tension, have you considered making a sleeve to reduce the I.D. between the bushings and squeeze the seal tighter? Maybe using a longer undersized bushing and machining an end for the seal to fit in would be easier to install.

    Leave a comment:


  • Steve Little
    replied
    I can't think of any use on a vintage Harley for this bigger model. It covers a range of 1.5" to 2.75".... perhaps fixing a galled kr-xlr crank pin.
    They're hellish expensive when new, and hardly ever come up for sale as pre loved.

    And then 2 are listed on eBay in one week. One is in Australia and one in Corvina LA.
    Stephen, step away from the computer ...You don't need this.



    http://www.ebay.com.au/itm/201679455144?ul_noapp=true

    I am expecting a call early this week from the Hard Chrome guy to come and pick up the two starter cranks.

    Leave a comment:


  • Steve Little
    replied
    Hi John. That's a possibility. There aren't any obvious marks to see on either of those arms.
    The kicker arms are an easy thing to check on a bike. I squatted down behind my 51 Pan and had a quick look and I could see that when I rebuilt that gearbox a few years ago, I installed a kicker that has a sharp bend.
    Last edited by Steve Little; 10-14-2016, 08:11 PM. Reason: grammatical flow

    Leave a comment:


  • TechNoir
    replied
    Originally posted by Steve Little View Post
    Anyone got any clues on the vintage of these "Soft bend" starter cranks?
    Could be a simple as that they all started out the same and then over the course of time a couple of bikes have been dropped and the cranks bent. Then the cranks have been straightened out and afterwards the bend looks slightly different to the originals?

    John

    Leave a comment:


  • Steve Little
    replied


    Anyone got any clues on the vintage of these "Soft bend" starter cranks?

    Leave a comment:


  • Steve Little
    replied
    Hi Bruce.
    I see it now you've pointed it out.
    Just up from the machined shaft, is the first bend which gives the kicker arm clearance from the muffler.
    All but two arms have a sharp, distinct, bend. The two that Bruce has identified don't.

    Leave a comment:


  • Bruce T
    replied
    G’day Steve, Informative thread as usual from you, thanks. Just a quick question relating to the photo of the seven 41-up starter cranks you posted with this thread. Counting the cranks from left to right in the photo, it appears that cranks 5 and 7 are slightly different than the others. The bends on these two cranks are more rounded. Do you know if there were two variations of the 41-up starter crank?

    Leave a comment:


  • Steve Little
    replied
    I don't have a NOS, OEM, shaft to measure, so I used a new #33096-54B JIMS shaft to determine the correct size.
    The JIMS shaft measures 2 tenths shy of 0.750”
    I'm guessing the tolerance is probably +000” /-0005”

    I tried a couple of “James gaskets #33076-37” quad seals on the JIMS shaft and it has excellent surface tension.
    After fitting the “James” quad seals to a range of under sized shafts, I can report that they loose contact with a shaft at about 0.733”
    I don't have any OEM seals, so cant make an assessment if they still hold at 0.733”

    James Gasket quad seals, still have minimal surface tension at 0.738” but my guess is they may leak through capillary action.

    I plan to get a couple of the smallest shafts Hard Chromed, and I will hone them to 0.750.

    Future Steve, will report back then.

    Feel free to debate, discuss, or write a scathing rebuttal, to any, or all, that I have surmised.

    Leave a comment:


  • Steve Little
    replied
    harleytoprock
    I never knew an external hone existed! A new learn. But why not just use a tool post grinder attachment on the lathe?

    Hi Toprock
    When I saw Bob's grinder in the "rocker arm" thread, I was struck green with envy. I don't have any type of precision grinder, but I can say that I'm enamoured with this external hone.

    I'm imagining a guy at Sunnen head office scratching his head and asking, what the hell's going on with all these FB hone enquiries?
    I'm feeling that, posting a picture of my collection is probably bad form.
    Also shows some level of my addiction for good tools. I will eventually purchase a FC as well.

    Leave a comment:


  • Steve Little
    replied
    Originally posted by BigLakeBob View Post
    I think what Steve is doing is great especially on the rocker arms, but I must say those kick arm shafts cut quite easily with a good grade of carbide. I have done quite a few then just make undersize bushings, just don't want to go too small, don't have that size in front of me right now.

    During the process of cleaning this lot up, Ive been thinking the same thing.
    The bushings are machined to the shaft size anyway, but I wonder what under size, the shaft stops making a "sealed" contact to the quad seal?
    I made some calls to a Hard Chrome, and metal spraying, companies a couple of days ago to enquire about costings.
    But the metal spraying also requires some more thought. The kicker arms are made of stout steel (Chrome Moli?) Metal spray involves a lot of heat. Will the kicker arm need to be tempered after machining if this process is used?
    I should say that I used the lathe to take the middle "high" section out of the shaft. This was to save the life of the hone stone. I finished off with the hone.



    Bring your knowledge to the table.

    Leave a comment:


  • BigLakeBob
    replied
    Originally posted by harleytoprock View Post
    I never knew an external hone existed! A new learn. But why not just use a toolpost grinder attachment on the lathe?
    I think what Steve is doing is great especially on the rocker arms, but I must say those kick arm shafts cut quite easily with a good grade of carbide. I have done quite a few then just make undersize bushings, just don't want to go too small, don't have that size in front of me right now.

    Leave a comment:


  • BigLakeBob
    replied
    Originally posted by T. Cotten View Post
    Many Thanks, Larry!

    My browser couldn't get past the chuck-like things on the left.
    Now if they would only offer a replacement belt for my LBN pedestal grinder; Carl O. gave me a serpentine belt number,... but it don't fit my fossil.

    I swear I will finally get a second lathe in duty this winter, I swear, and most likely I will be conjuring flatbelts for it as well as the ancient Sunnen.
    (A fellow at Davenport gave me a critical clue for a source... but it doesn't browse up for me either.)

    Steve's efforts are most admirable!

    ....Cotten
    I get all my flat belts from McMaster, from my old Southbend, B&S OD Grinder, and Sunnen Hone.

    Leave a comment:


  • T. Cotten
    replied
    Originally posted by harleytoprock View Post
    I never knew an external hone existed! A new learn. But why not just use a toolpost grinder attachment on the lathe?
    Well harleytoprock,

    Although I have no experience with the Sunnen external hone, my experience with toolpost grinders suggests to me that it would be a lot faster, easier, and more certain of result.

    (But then the toolpost grinders available to me were as much a piece of crap as the rest of the machinery.)

    If you have only a few pieces to carve, go for it!

    ....Cotten
    Last edited by T. Cotten; 10-06-2016, 05:14 PM.

    Leave a comment:


  • harleytoprock
    replied
    I never knew an external hone existed! A new learn. But why not just use a toolpost grinder attachment on the lathe?

    Leave a comment:

Working...