Nobody's going to bring up ultrasonic cleaners, Folks?
(I wasn't impressed either.)
.....Cotten
bead blast or not
Collapse
X
-
From Vapor Hone web site.
VAPOR HONING
Is a process that propels pressurized air mixed with abrasive and water at a surface to clean or prep for paint. Also known as hydro blasting, wet blasting, aqua blasting, slurry blasting, liquid honing, and vapor blasting.
Abrasive added...
Leave a comment:
-
I guess, (since there seems to be differing opinions) that checking with the person performing the service would eliminate any doubt prior to (possibly) an undesired result. Pressure washing with some (any) kind of blast media sounds like the often seen ads for the Dustless Blasting machines on TV. I believe that ANY blast media would not be needed with the right VAPOR and pressure. That would be the whole point of selecting this method. Ask Questions first! .......Smitty
Leave a comment:
-
We all know exactly what they looked like fresh, right Folks?
Its been nearly two decades since I played with cases, but I still play with aluminum carb bowls, and faking it is still faking it.
(Its harder when the judging customer can hold the work in the palm of his hand and focus, believe me!)
If your motorcases do not need a lot of special attention, and pre-prep, and de-prep,.. ...
They must be NOS.
....Cotten
PS: Yes, I coat inside of bowls, where prudent for other reasons.Last edited by T. Cotten; 03-15-2022, 02:05 PM.
Leave a comment:
-
Yes Vapor Hone uses abrasive (glass bead or Ceramic and others), In simple terms its like a pressure washer with media in the jet stream. Eliminates dust and cleans the part. I don't know what the Judges say but it is clearly not the same finish as "when it left the factory"
Leave a comment:
-
Is that not always the final step anyway, Larry?Originally posted by larry View PostIn spite of all the cleaning systems just discussed, I still prefer scrubbing in a sink with common household cleansers and warm/hot water
Blasting, no matter the media, is a labor-saving device, preparing surfaces before the final scrub.
Obviously, a "restoration" cannot be treated the same as a "conservation".
So what's in style with the judges?
....CottenLast edited by T. Cotten; 03-15-2022, 11:14 AM.
Leave a comment:
-
In spite of all the cleaning systems just discussed, I still prefer scrubbing in a sink with common household cleansers and warm/hot water
Leave a comment:
-
I thought vapor honing was the process that used dry ice as the media. If so it leaves no residue nor does it damage anything. I remember being involved when it was used to clean a 440 volt substation. It did not even damage the insulation on the heavy cables. Pretty impressive. Just vacuum up what the blasting media removed.
Leave a comment:
-
Maybe I'm wrong but I don't believe that vapor honing uses any sort of blast media. On the parts done with vapor honing that I have seen, there was no change in "texture" to any of the parts (including cases). To me, it looks like the optimal method to achieve the cleanest possible parts, but checking the procedure with the person who will be doing it would confirm how and with what will be used by that particular person. Just so there's no misunderstanding and an unwanted finished result. Hope this helps......Smitty
Leave a comment:
-
Looks like it has a decent mil-profile to hold paint, Larry!
Beads don't, but I haven't a place for a fifth blast cabinet, and can't pass on the cost to the customer. I would still be brushing the internals anyway.
And you really want a sealer, Stroker, for the three reasons I gave.
The factorys thought so too, and that's why they used the 'red stuff' that no longer resists fuels. Either we search for a modern fuel-proof sealer, or bake-on Glyptal and make certain the petcock is absolute.
For the external appearance, we must first decide whose eye we must please.
An individual can take great pride, and a whole lot of time and effort, to produce a decent finish, but a pro shop would have to charge hundred$, so that's why we blast, prep, and seal, when necessary.
....CottenLast edited by T. Cotten; 03-14-2022, 09:47 AM.
Leave a comment:
-
sodam74.JPG An example of soda blasting. Looks like conventional blasting, but no grit. Washing in water dissolves residue.
Leave a comment:
-
I stopped bead blasting motor, and transmission cases in favor of hand washing, and scrubbing. I use a variety of cleaners, brushes, Scotch-brite, and chemicals to make the aluminum castings clean but I strive not to change the texture of the castings. I like the look of cleaned aluminum, and think it's much closer in appearance to an original casting.
Leave a comment:
-
the cases are very strait no repairs. inside was coated with some red looking sealer with half worn off or missing i am going to remove the remainder and try no sealer unless there is some bullet proof good stuff any opinions going with no coatings? also is it safe to boil the cases to remove any residual blasting media thanks in advance for opinions and advice
Leave a comment:
-
The last couple of projects that I did that involved complete engine disassembly I blasted the aluminum engine cases with 80 grit glass beads at about 60 p.s.i. and as a final clean-up put them in an heated ultrasonic cleaner. A guy I know has one large enough for cases. It gives you a little extra piece of mind that nothing should be coming out of the pores in the aluminum.
Leave a comment:
-
Basically, Stroker,..Originally posted by stroker View Postyes what is encapsulating
Its just painting the internal surfaces not only to lock down any residual abrasives, but to seal any porosities, and let the oil settle to the sump better.
The traditional coating was 'Gasoila', but there has got to be an improved formula today. Baked 'Glyptal' became the standard for decades, but it also suffered from any leakage past a petcock that might enter the motor while sitting. OHV's are most prone to this issue.
Unfortunately, although there may be many fine coatings, constantly changing modern fuels do not treat them all the same.
Back to the externals, are there any repairs or blemishes to dress before a final finish? Judges like to point their fingers at things like that, if they can't find anything else.
.....CottenLast edited by T. Cotten; 03-13-2022, 02:56 PM.
Leave a comment:
Leave a comment: