flathead front cylinder cold as bike is running

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • dukekleman
    replied
    Sure thing,
    The engine will run on that cylinder at 20-25% leak, however it will exhibit combustion inefficiencies above that.

    I have had success restoring higher leak rates on flatheads above the stated percentage values without dissembling the engine.

    Please post the measured leak percentage and I'll be happy to help and advise based off that number.

    Duke

    Leave a comment:


  • tfburke3
    replied
    Originally posted by SamJ View Post
    Reviving an old thread here: I recently picked up a 49 WL, and it's running on rear cylinder only. I tried different plugs, replaced coils and wires with Bulldog Bros (great guy to deal with btw), but still only rear firing. Is my next step the intake manifold? Any other rabbit holes to go down? Bike is a mostly-original, mostly-unrestored barn-find. It has all new wiring, coil, plugs, wires & battery, plus carb has been overhauled. Points/condenser are old.
    I would start by inspecting point contacts and gap.If they are God the condenser is probably fine.If they are pitted start with new points and condenser,
    Tom

    Leave a comment:


  • T. Cotten
    replied
    Originally posted by dukekleman View Post
    SamJ,

    Have you confirmed the condition of the front cylinder that isn't firing by performing Compression and leak down test?

    Duke
    Great idea, Duke!

    Can you give us base-line parameters for the leak-down on a 45"?

    Thanks in advance,

    ....Cotten

    Leave a comment:


  • dukekleman
    replied
    SamJ,

    Have you confirmed the condition of the front cylinder that isn't firing by performing Compression and leak down test?

    Duke

    Leave a comment:


  • T. Cotten
    replied
    I typed a long reply to your personal message, Sam!

    Honest I did, but this forum's format sucked it up and it disappeared.

    Please feel free to email me direct at Liberty@npoint.net for my test equipment prices, but I encourage you to innovate instead!

    (Self-reliance is pretty intrinsic to enjoying these machines.. Computers not so much.)

    ....Cotten
    PS: Re-clicking my email notification brought up the ghost of my attempted reply, but wouldn't let me edit my successful reply. PMs ain't worth it.
    Last edited by T. Cotten; 04-12-2024, 12:10 PM.

    Leave a comment:


  • SamJ
    replied
    Awesome advice, looks like I got my work cut out for me!

    Leave a comment:


  • T. Cotten
    replied
    Originally posted by SamJ View Post

    Thank you for the reply, sir. I'll start looking for a testplate ASAP.
    If you cannot carve your own, Sam,...

    Mine are ABS plastic with a simple nipple, instead of a stupid Schrader valve like ebay gems.

    TESTKIT.jpg

    It you find a leak, the manifold must be removed, and the inlet nipples tested separately with some sort of plug, and mine are rubber stoppers perforated for a nipple.

    Anything that fits will do!:

    PATRON.jpg
    But it takes three hands.

    ....Cotten
    Last edited by T. Cotten; 04-12-2024, 10:39 AM.

    Leave a comment:


  • duffeycycles
    replied
    pull the front plug & quickly pass a propane torch over the plug hole & clear any fuel from the cylinder
    --------------------------
    When running,pull the spark plug wire off the not firing, front cylinder.
    Hold the wire close to the plug electrode a see if it starts to fire or if there is spark at all.
    Sometime a severely fouled cylinder will clear itself.
    Right after a severe rain at Wauseon bikes were soaked,My servi had water standing on the heads around the plugs.
    Many watched me try to start my servi,making jokes that there was no way it would.
    Started on rear cyl only,removed wire to front,held close & it quickly cleared itself & I rode away.

    Leave a comment:


  • SamJ
    replied
    Originally posted by T. Cotten View Post

    Your instincts are good, Sam!

    https://virtualindian.org/11techleaktest.html

    Good Luck!

    .....Cotten
    Thank you for the reply, sir. I'll start looking for a testplate ASAP.

    Leave a comment:


  • otis71
    replied
    Easy to diagnose. Pull the spark plug wire off the running cylinder and it’ll stall if the other isn’t firing.

    Leave a comment:


  • T. Cotten
    replied
    Originally posted by SamJ View Post
    ...Is my next step the intake manifold? ..
    Your instincts are good, Sam!

    https://virtualindian.org/11techleaktest.html

    Good Luck!

    .....Cotten
    Last edited by T. Cotten; 04-11-2024, 07:32 PM.

    Leave a comment:


  • SamJ
    replied
    Reviving an old thread here: I recently picked up a 49 WL, and it's running on rear cylinder only. I tried different plugs, replaced coils and wires with Bulldog Bros (great guy to deal with btw), but still only rear firing. Is my next step the intake manifold? Any other rabbit holes to go down? Bike is a mostly-original, mostly-unrestored barn-find. It has all new wiring, coil, plugs, wires & battery, plus carb has been overhauled. Points/condenser are old.

    Leave a comment:


  • BigLakeBob
    replied
    You still may want to keep a watch on the coil, wires or intake leak, it could have just been a plug but something else may have caused it to foul.

    Leave a comment:


  • Streetbobber74
    replied
    gerry
    thank you very much, swapped out the front plug, which was just nasty black, bike fired up on the 2nd kick. sometimes its the obvious stuff right in your face you don't see. thanks again.

    Leave a comment:


  • Streetbobber74
    replied
    I'm very new to the older bikes, as this is my first kickstart, how will i know if the front cylinder is firing every time, is there a way i can check that? can't thank you enough for the quick response. i just picked up some new plugs gonna try that, tonight or in AM. i have not had the timer out of the case at all.
    just got the bike myself a few weeks ago.

    Leave a comment:

Working...