Hard starting 1964 R69S

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Coolbreeze
    replied
    The problem was a worn spark advance!! I replaced it and the R69S started on the first kick. There are times it is a bit reluctant to start, but that may be because the Bing carburetors are worn. I have taken it on several trips this past fall, and was able to make it home each time. After the BMW and I have our valves worked on this winter, we should be ready for more and longer tripts this year. Again, thank you all for your input.

    Leave a comment:


  • jim d
    replied
    Did you do what I suggested in my earlier post? In regard to taking the magneto and related ignition components apart and give them a thorough cleaning with a scotch brite like material and use an electrical compound to promote a good ground and retard corrosion. Most of the magneto systems on these bikes are over 50 years old and never had this area addressed. The parts may not look that bad but the combination of all of the components having some oxidation can result in a bad or intermittent grounding of the magneto.

    Leave a comment:


  • PaulCDF
    replied
    Bummer!
    Have you spoken with Dave Fahringer yet???

    Leave a comment:


  • Coolbreeze
    replied
    Shortly after getting the R69S back from Dave Fahringer, it reverted to being almost impossible to start. Look at my posts this month on this forum to see how it was returned to the level of reliability one expects from a /2 BMW.

    Leave a comment:


  • ryan
    replied
    Glad you got your bike running well. You have a nice collection!

    Leave a comment:


  • Coolbreeze
    replied
    1. Joined Airheads
    2. Found Dave Fahringer who volunteered to get my R69S to start like it should.
    3. Dave found the magneto was time correctly as far as the points were concerned, but was not timed correctly as far as its orientation on the engine. It needed phase adjustment.
    4. Now, it starts better than it ever has.

    If I understand the problem correctly, the magneto was bolted on the engine block slightly crooked. I had no idea that was even possible.

    Leave a comment:


  • PRG
    replied
    Howdy sir,

    View the last pic of the offering to which George is referring which is in the link below. Note there is nothing attached to the camshaft or any components of the mag remaining. Though touted as a 12 volt conversion far more significant is a hybrid adaption of CD (capacitive discharge) ignition - if similar to my BTH sourced version - which includes built in analogue auto advance. This latter feature is what he is focusing on.

    CD ignition is known for its powerful spark at low starting cycle rpm and resistance to dry fouling at high cylinder pressures and was put on the mainstream map by Porsche in 1968 with the fitment of the American sourced Permatune to their 911 range for which the most powerful version, the 911S, had reached its ignition limit at roughly 90hp per liter. BTH's offerings absolutely transform the usability of a Vincents and Velocettes and I see no reason why this ignition, if indeed CD based, would not do the same for /2's. If nothing else it would get rid of the fiddly points, increasingly rare NOS replacement parts and sometimes wobbly points cam. I need to drag mine back out from the back of the shop and sort out what is likely a simple issue.

    https://www.ebay.com/itm/BMW-Powerdy...tYjUbW&vxp=mtr

    Leave a comment:


  • jim d
    replied
    Have you checked out the Vintage BMW Owners Club website? There is a wealth of information on there. You can go on as a guest. Sometimes it is as simple as removing the mag. and cleaning everything to make sure of good grounding and contact areas. Over years of time resistance can build up in those areas that will affect the ignition. There was a discussion on that on the site. A 12 volt conversion will only affect the charging area, not starting which is controlled by the mag. coil, points and condenser. There is a download available by Don Rickles called Understanding and Maintaining The BMW /2 electrical System. It is 28 pages long and well worth being in your tech. library. Replacement condenser late 60s Ford NAPA # FA82.

    Leave a comment:


  • Coolbreeze
    replied
    Originally posted by Lyle Manheimer View Post
    Wow, a bit pricey for me. My '65 R50 became hard to start and it was determined to be the mag coil. When the bike was warm it was hard to start due to expansion of the mag coil and the resulting "open" in the coil. Finally it failed and would not start even when cold. Replaced the mag coil and all is fine. Once again a true one kicker. I never had the magnets re-energized.
    Thank you for your input. I have replaced my coil twice, with no improvement.

    Leave a comment:


  • PRG
    replied
    Howdy sir,

    Not all condensers are the same, they are rated in microferads and this becomes very apparent/important at either end of the coil output scale. I'd be inclined to remagnetize and if not satisfactory go from there.

    I did an early version of this latest conversion as depicted in the pics below. Admittedly this was the last one in a very small batch done by someone who primarily focused on Vincents, created this kit for his own use, then tried it on the BMW market which proved to be far tighter with their purse strings for the cost involved, and he subsequently abandoned the project. I cast no assertions on the effectiveness or lack there of but will say this. It includes a 100 watt alternator which would not keep up with a 50 watt halogen low beam in urban use. Prior to my purchase, my R69S had been ridden the entire time in locations with very low octane gas and therefore had rather low compression via cylinder base gaskets. When doing this conversion removed them reverting to the stock configuration with noticeably more compression. With this kit fitted my machine became more persnickety to start but the most annoying was plug dry fouling under high cylinder pressure, i.e., large throttle openings at low rpm under load. Was it a system ground problem, don't know, parked this machine over 5 years ago and never pursued remedy. Many of these kits now were/are modeled after mine, be sure to research before selecting one.

    This view shows the condensor, a rather funky setup in that NOS spares have no wire attached. One has to solder on their own at the risk of overheating the unit. Also visible is the advance setup, the most outboard placed item and the source of the most issues with this ignition system. They consist of eratic advance caused by inappropriate tensioned springs or worse, a points cam that is not symetrical to each cylinder resulting in one firing before/after its intended points which leads to shadowing of the timing marks on the flywheel when pointing a strobe at it. This by far was my principal motivation for fitting a BTH.

    Leave a comment:


  • Lyle Manheimer
    replied
    Wow, a bit pricey for me. My '65 R50 became hard to start and it was determined to be the mag coil. When the bike was warm it was hard to start due to expansion of the mag coil and the resulting "open" in the coil. Finally it failed and would not start even when cold. Replaced the mag coil and all is fine. Once again a true one kicker. I never had the magnets re-energized.

    Leave a comment:


  • Coolbreeze
    replied
    A "BMW Powerdynamo 12 volt conversion kit" is offered on Ebay for $675. Has anybody tried this conversion? This may correct the temperamental starting R69S. I have tried all the tuning tricks, but have not re-energized the magneto magnet yet.

    Leave a comment:


  • Somer
    replied
    My 1st suspicion on BMW /2's is the condenser. Get one with a pigtail from an auto supply. All condensers are the same. See if that helps.

    Leave a comment:


  • Rubone
    replied
    Just find an old tractor repair shop and get your magnets recharged.

    Leave a comment:


  • Coolbreeze
    replied
    Thank you for the suggestions. I may ask Morris Mag if they will sell me a set of rare earth magnets cut to the correct dimensions.

    Leave a comment:

Working...