I'm a little late coming to this thread but I just got done reading all 56 pages. Much respect & admiration for the work you put into the restoration and running in the Cannonball.
That had to be quite the endeavor. Good luck in your future runs. Bill
Announcement
Collapse
No announcement yet.
Powerplus or Bust, Eh?
Collapse
X
-
Originally posted by Olie View PostWhere did you get your new clutch disc's at?
Kevin
.
Leave a comment:
-
Mounting da clutch
I covered assembling the clutch in an earlier post. In order to mount it, you have to disassemble it back to the point that the hub can be slid onto the tapered output shaft of the transmissionand the nut can be installed. Remember to put the key in the key way. Here is a picture. Note that the back plate and sprocket are still on the hub:
Before the nut goes on, there are two lockwashers that go on. A larger on that gets peened into the slot in the lock ring and a smaller one that goes through a hole in the larger one and into a hole in the hub:
Here's what it looks like with the nut on. Remember that the nut has left handed threads. I used locktite.
Then the inner clutch disc with the pretty new Kevlar lining goes on:
The outer disc goes on next. You might have to lean the bike over to the right a bit to convince all the discs to stay in place for now.
Then you slide the spring plate and springs in place. You can use as many as 16 springs. In this picture I have install 8, that is where I started. After riding the bike and fiddling with the adjustments, I ended up at 12 springs being the the best number for me.
Then the spring tension plate goes on with the tension plate adjusting screws and lock plate as I showed earlier.
Kevin
.Last edited by Shaky Jake; 03-12-2017, 09:10 PM.
Leave a comment:
-
Back in time
So, I was looking through this blog and I see that, in the final rush to the start of the '16 Cannonball, I had to skip a few details in the build. Now that I've given you a taste of the Cannonball itself, I want to step back in time to cover those details.
The things I see that I haven't covered yet in the making of Patience are, the clutch, the carburetor, the exhaust pipes, the oil tank & chain guard & other miscellaneous tins, the steering stops, how the compression release works, the Cannonball wheels, the lights, the luggage rack, the spare transmission, and a few other little details. So stay tuned for that.
I also have plans to make some improvements for 2018 that I'll cover because, as I said earlier, my goal next year is to not only do all of the miles, but to spend less time working on the bike and more time having fun with my friends. On that subject, I came to realize that I met a lot of you all last year and I don't have any pictures with any of you. That is just wrong. Please, if I meet any of you next year make sure that I get a picture of us to post. Most of the folks that I met were at the finish line when I rolled in. It was always a thrill for me to meet someone who is familiar with the blog. At that moment that I roll across the finish line I'm usually tired and thirsty and hungry and looking for the van. And on many nights there is a planned dinner to attend. Here's a tip: if you want to get a flavor for the Cannonball, walk around the hotel parking lot after dinner. On most nights there's a good chance that most everybody will be drinking beer and working on their bikes in the parking lot.
Anyway, I'm going to get started organizing some of my pre-Cannonball built pictures, and I'll plan on getting them posted up soon.
Kevin
.
Leave a comment:
-
Originally posted by BoschZEV View PostMy reason for looking for a British bike is that "everyone else" will be on Harleys or Indians and I wanted something out of the mainstream (although I wanted something different, I didn't want to pay $100k for a Henderson to be that different). I'm not being coy in not mentioning the bike itself but I don't want to jinx it until its age has been confirmed.
Kevin
.
Leave a comment:
-
Originally posted by Shaky Jake View PostI actually texted you a few days ago asking if you found a bike yet. I'm guessing you were out of the country at the time. Are you going to have a build thread?
I'll definitely have a comprehensive build thread, but probably not on this site. The bike is British so there are other sites better suited for that.
As I'm sure you know, pre-'29 British bikes are pretty short on the ground in the U.S., and those that are here have been restored so they look great on the outside, but all too often not-so great on the inside, so a complete rebuild is needed to minimize the chance of you passing me broken down on the side of the road. Anyway, after chasing a half-dozen promising leads around the world I finally found "my" bike in Europe. I'll have it confirmed at the end of the week that it indeed is the '27 or '28 (and not a '29) the owner is "pretty sure" it is. The owner is currently in the U.S.
My reason for looking for a British bike is that "everyone else" will be on Harleys or Indians and I wanted something out of the mainstream (although I wanted something different, I didn't want to pay $100k for a Henderson to be that different). I'm not being coy in not mentioning the bike itself but I don't want to jinx it until its age has been confirmed.
Leave a comment:
-
Originally posted by BoschZEV View PostCongratulations on these awards, but most of all congratulations for having successfully ridden from coast to coast with full points on a century-old bike you completely rebuilt yourself at no small effort.
After almost two months of searching last week I finally found something that met my "specifications" so today I bit the bullet and put down my non-refundable deposit (I would have done it last week but I was out of the country and I won't do anything financial over hotel wifi). Unless you use a different bike in 2018 I'll be in a different class than you (i.e. pre-'29 single) but should see you every morning and evening, if not along the way each day as well (hopefully, not with you passing me broken down on the side of the road...).
Kevin
.
Leave a comment:
-
Originally posted by Shaky Jake View PostI thought I'd show off these awards that Patience earned at the Lincoln Highway National Meet in Lincoln, NE.
After almost two months of searching last week I finally found something that met my "specifications" so today I bit the bullet and put down my non-refundable deposit (I would have done it last week but I was out of the country and I won't do anything financial over hotel wifi). Unless you use a different bike in 2018 I'll be in a different class than you (i.e. pre-'29 single) but should see you every morning and evening, if not along the way each day as well (hopefully, not with you passing me broken down on the side of the road...).
Leave a comment:
-
I thought I'd show off these awards that Patience earned at the Lincoln Highway National Meet in Lincoln, NE.
She got a Century Medallion and pin, a Century Recognition certificate, and a trophy cup for Period Modified. As you can see, we already put the cup to good use.
Kevin
.
Leave a comment:
-
Originally posted by McLean Motors View PostHi Kevin.
Sorry for the delayed response. This Friday my clutch will come back from Energy One. Yes, Kent is the guy's name and he seems like a true enthusiast.
If you're still interested in the single speed cluch, let me know and we can take it offline.
Congratulations on completion of the Cannonball. Hell, congratulations on merely attempting.
All the best,
Shawn
Kevin
Leave a comment:
-
Originally posted by Shaky Jake View PostShawn,
Energy One Performance Clutches can re-line your clutch plates for the powerplus three speed clutch. You have to send them your plates with the old lining removed, and they bond modern material to them, Kevlar I think. It was about $90 a set if I remember correctly. Their number is 562-404-5200, I think the guys name was Kent.
I have been wanting to build a single speed powerplus twin, so if you have any interest in parting with you pedal parts, please messsage me. I would pay cash or consider parts trades. Just let me know.
Kevin
.
Sorry for the delayed response. This Friday my clutch will come back from Energy One. Yes, Kent is the guy's name and he seems like a true enthusiast.
If you're still interested in the single speed cluch, let me know and we can take it offline.
Congratulations on completion of the Cannonball. Hell, congratulations on merely attempting.
All the best,
Shawn
Leave a comment:
-
Thanks Kevin for documenting your build including acquiring the motorcycle and the trip to BC to pick it up all the way through your Cannonball run. I am a hopeless "build" fan and even resort to following off grid cabin builds and garage builds on other forums. Your photos gives somewhat of a sense of the difficulty of the runs. Keep up the good work.
Mike Love
AMCA 19097
Leave a comment:
-
On the 25th we had lunch in Temecula, then it was on to Carlsbad where Patience got her final sticker:
Some of Paul's old friends that live in the area, so they came with us to the Banquet that night:
Joe Walano's T shirt summed it up. Now we know...
Kevin
.
Leave a comment:
-
This is what I wrote on my Facebook page on September 24:
Patience didn't care for this mornings ride through the desert. She's worn and tired and struggling on every uphill mile. For me, this was the most beautiful leg of the journey. The air was crystal clear and still. The sky was blue like a husky's eyes. The texture and stark clarity of the mountains in the distance was striking. The patterns formed by the sage and mesquite as it spread into the distance were almost geometric. Someday I'll bring a camper out here and stay a while, just so I can look at it every day. I tried to take a picture, but you just can't photograph a mountain.
Once again, DAN provided the entertainment in the hotel parking lot.
Kevin
.Last edited by Shaky Jake; 02-11-2017, 01:20 PM.
Leave a comment:
Leave a comment: