Moto Guzzi 500 cc GTV question

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • stanfromhell
    New Member
    • Nov 2026
    • 3

    #1

    Moto Guzzi 500 cc GTV question

    I have a 1948 Guzzi GTV Bacon Slicer hat is in great running condition, every thing works as it should except the speedometer. The bike is not immaculately restored, it has patina and the paint shines but shows its age. I am 78 yrs old and it's time to sell it. My problem is... I can't find out what the value of it is. I've searched countless sites including Hagertys, Bonhams, Guzzi forums etc etc and all I could find was one older museum quality GTV that sold for 25K. Any suggestions about where to look or bikes you know of that have been sold would be greatly appreciated
    You do not have permission to view this gallery.
    This gallery has 1 photos.
  • chuckthebeatertruck
    Senior Member
    • Jun 2018
    • 697

    #2
    Fellow 1948/49 GTV owner here. Mine was built in summer ‘48.

    These models are exceedingly rare in the US and trade hands privately.

    Generally, fully restored and well sorted “pretty” bikes can trade at $12-15k. I know of a few that went for more, but that was a few years ago and it’s now a buyers market on these big thumpers.

    Good solid runners can trade at $8-10k.

    Most people will offer you 5-8k.

    Comment

    • JoJo357
      Senior Member
      • Feb 2016
      • 3304

      #3
      Great looking Guzzi Stan. I hope the GTV finds a nice home. *Good Luck.

      *M.A.D.*

      Comment

      • Peter Cooke
        Senior Member
        • Aug 2012
        • 572

        #4
        Nice bike. Where does 'Bacon Slicer' come from?

        Comment

        • stanfromhell
          New Member
          • Nov 2026
          • 3

          #5
          "Bacon Slicer " comes from the exposed flywheel spinning about two inches away from your left calf. Like a meat slicer at your local Deli

          Comment

          • Peter Cooke
            Senior Member
            • Aug 2012
            • 572

            #6
            Originally posted by stanfromhell View Post
            "Bacon Slicer " comes from the exposed flywheel spinning about two inches away from your left calf. Like a meat slicer at your local Deli
            That'd do it! Thanks for that.

            Comment

            • chuckthebeatertruck
              Senior Member
              • Jun 2018
              • 697

              #7
              Originally posted by stanfromhell View Post
              "Bacon Slicer " comes from the exposed flywheel spinning about two inches away from your left calf. Like a meat slicer at your local Deli

              There are two things that constantly stop people when they see my GTV out and about: 1) It has exposed valves -- folks just get fascinated by watching the valves work as the motor idles. Occasionally it occurs to someone there's no lubrication to the valves and then they get the funniest look on their faces and 2) not only is that big old 23 pound flywheel spinning away -- it spins "backwards" compared to 99% of motorbikes. Again, more people just stare and stare and stare at that flywheel rolling around.

              Then, two more things happen in short order: 1) they notice it has no kill switch or key anywhere. When you tell people you either pull the decompression lever or put a hand over the carb mouth to stop the motor - well, they just stare at you. and 2) the heel brake. I've had more people freak out over the heel brake than almost anything else.

              Then there is the fun of watching people accustomed to big British Singles go to start the bike. Their technique is almost always off and the bike will kick back a good un if you don't kick through. It's not the 500cc -- it's the flywheel effect. Once you get that flywheel moving -- the motor neither speeds up nor slows down very fast. That does have a very positive benefit in that it makes the bike beyond easy to ride. If you can stall a 500cc Guzzi single while taking off - you've accomplished something.

              And for posterity, the reason these bikes are so rare isn't just because they are Italian.

              Basically, Guzzi got shut down by the war and wasn't really able to get back into production until the second half of 1946. There was almost no demand for big bikes due to purchase costs and also lack of fuel. Guzzi really didn't have a market for the 500cc bikes - but they also didn't have another model to succeed them. Guzzi sold a LOT more small capacity bikes than these big 500s.

              So,they just kept producing the prewar bike for a couple of years until the upgraded design, known as the Astore, came out in late autumn 1948 (1949 model). The main upgrades were an alloy cylinder and enclosed valve gear. With the Falcone; which succeed the Astore; the crash box transmission from 1934 was also replaced. Oddly, Guzzi reverted from hydraulic dampners to friction disc knee action suspension. I really don't know why . . .I find the hydraulic dampers surprisingly brilliant.

              When you see a 1947 or 1948 GTV or GTW in the US, you're seeing a bike that made it to these shores in numbers approaching not much more than 100 bikes. You will find a dozen Falcone and two dozen Airone for every GTV you find - maybe.

              Oh, they didn't come with a speed or a stop lamp either - just a tail lamp. If you have a MPH speedo - covet it as they are super rare. Most are KPH speedos.

              I am, however, happy to report that the one crazy to find part - the carbon pick up for the marelli magneto is back in reproduction. Almost always the originals fracture when you extract them from the mag when pulling the armature to regrease the bearings or repair/rebuild the magneto. They are, however, 85 euro.

              Comment

              Working...