Search:

Type: Posts; User: slamiste

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Hi Temple, I need a harness for a 1957 FLH. I...

    Hi Temple,
    I need a harness for a 1957 FLH. I would like the wires to be woven where they should be instead of the fat loom used on harnesses I've used in the past. Were you satisfied with the...
  2. Replies
    6
    Views
    184

    Agree. Only the FLH models.

    Agree. Only the FLH models.
  3. Replies
    6
    Views
    184

    Thanks Robbie, I was able to blow it up enough...

    Thanks Robbie,

    I was able to blow it up enough to tell me what I needed. I'm glad I asked since the placement shown is different than I had planned.

    Steve Slaminko
  4. Replies
    6
    Views
    184

    FLH oil tank decal placement - 1957

    Can anyone supply a close-up photo of the "correct" placement of the FLH decal on the oil tank for a 1957 FLH? A factory photo or a photo of the decal on an original machine would be most helpful.
    ...
  5. Great video. Thanks.

    Great video. Thanks.
  6. Thanks Robbie.

    Thanks Robbie.
  7. Oil seal cork washer behind main drive sprocket 1957 Panhead

    Hi,
    I'm changing the oil seal (2163-36) behind the sprocket on the transmission from my 1957 FLH. Behind the oil seal is part number 2163-36B - oil seal cork washer. I don't have this part. Local...
  8. Replies
    5
    Views
    396

    Thanks everyone, The information supplied will...

    Thanks everyone,

    The information supplied will allow me to pick which ones to buy.

    Cotton - The JD carb is stamped HX154.

    Steve Slaminko
  9. Replies
    5
    Views
    396

    HD Special thread pitches

    I'm planning on ordering taps and dies for the "special" thread pitches used on early Harleys. I primarily work on Big Twins from the 30's to the 60's but I'm also working on a 1924 J model. I'm...
  10. Replies
    6
    Views
    434

    Here's what's on my 32. I can't be sure these...

    Here's what's on my 32. I can't be sure these are correct for 32 so I'm probably just adding another layer of confusion. These bars are pretty wide measuring 36 - 37 inches from grip end to grip...
  11. Replies
    2
    Views
    560

    Welcome back!

    Welcome back!
  12. Replies
    19
    Views
    1,841

    I use an old gas cap with a cork or old rubber...

    I use an old gas cap with a cork or old rubber gasket for the gas fill area. For the other openings I use rubber stoppers or plastic cap plugs. None of these materials is acetone resistant for long...
  13. Replies
    3
    Views
    478

    Thanks Robbie, I need to dig out the set where...

    Thanks Robbie,

    I need to dig out the set where the rubber has completely separated from the riser. Based on your description I'm guessing the steel sleeve remains in the risers. As I remember...
  14. Replies
    3
    Views
    478

    49 - 57 Handlebar Riser Repair

    I've got 2 sets of 49 - 57 handlebar risers where the rubber bushings are loose (one set) and one set where the bushings are totally separated from the steel shell. Can these be safely repaired? if...
  15. Replies
    8
    Views
    986

    Chris and Robbie, Thanks guys. Picture is a...

    Chris and Robbie,

    Thanks guys. Picture is a big help. Your help with my many questions over the years is always appreciated.

    Steve Slaminko
  16. Replies
    8
    Views
    986

    Chris, I was hoping to have the exploded view...

    Chris,

    I was hoping to have the exploded view to make sure I get the correct hardware and also to insure I get the whole thing assembled properly. Palmer gives a pretty good description of the...
  17. Replies
    8
    Views
    986

    1938 Horn Assembly to Fork

    Can anyone supply an exploded view of the horn to fork assembly for a 1938 big twin? My parts books only have the view for the later version. I checked the virtual library and didn't see anything...
  18. 1950 FL throttle / spark control cable inner wire reach

    I'm working on a 1950 FL. Can anyone tell me how far the inner cable is supposed to move linearly in relation to the outer cable when the twist grip is rotated from one direction to the other. I...
  19. As for the 4th gear whine on a V700. I didn't...

    As for the 4th gear whine on a V700. I didn't ride the bike much but I don't remember the gear whine being excessive in 4th gear. All the gears had a satisfying whine that reminded me of my old hot...
  20. Thanks for this Steve, I worked on nothing but...

    Thanks for this Steve,

    I worked on nothing but old Harley and Indians for years when my youngest son brought home a early V700 Guzzi in just awful condition. The motor was stuck and everything...
  21. Thanks everyone!

    Thanks everyone!
  22. Thanks Tom. I thought of Old Dude but his web...

    Thanks Tom. I thought of Old Dude but his web site doesn't tell you much about what he has. I'll try the "Parts Request" thing and see if that works.

    Steve
  23. Screw for attaching the gas tank emblems on 1948 tanks.

    The screw used to attach the gas tank emblems on a 1948 HD is shown as part number 3508-47A. Can anyone tell me a common hardware store replacement or where I can get the actual HD part. I don't...
  24. Harley Big Twin Rigid Frame - Rear Sidecar Connect Fasteners

    I'll be mounting a sidecar on a 1957 Panhead. I need the fasteners for the rear sidecar mount to frame. Parts numbers are Bolt - 6036-36 (new # 4979), Check Nut - 6036-36B (7938) and Castle Nut -...
  25. Keith, I sent you a PM yesterday. Did you...

    Keith,
    I sent you a PM yesterday. Did you receive it? I'm relatively new to that feature and I don't see a record of me sending one. Let me know.

    Steve
Results 1 to 25 of 199
Page 1 of 8 1 2 3 4