Search:

Type: Posts; User: Steve Little

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Ok. Hopefully this is a less harder...

    Ok. Hopefully this is a less harder question...can anyone clear up what years these "gear shifter cams" correspond to?

    28550
  2. K model and Sporty part identification

    Hi. Hope everyone is well.
    A bit over a year ago I bought a large quantity of iron head Sportster parts to try and get a few of my projects completed.
    During the clean and identification of these...
  3. There is no laughing emoji.... but I am. Thanks...

    There is no laughing emoji.... but I am. Thanks for contributing.
  4. Hi kitabel. I appreciate you taking time to...

    Hi kitabel. I appreciate you taking time to reply.
    I am thinking you are relating crank pin tapers. The crank pin tapers on my XLRs are the same as Sporty and Big twin and I have that bob weight in...
  5. WR, KR, XLR, and early XR balance spindle

    Hi. Hope everyone is well.
    Wondering if anyone knows if S&S, Eastern or Enfield or any other manufacturer makes a balance spindle for any of the Harley R series race engines?
    Harley might have...
  6. Replies
    9
    Views
    654

    Thanks Robbie.

    Thanks Robbie.
  7. Replies
    9
    Views
    654

    Hi Robbie. Sorry. I'm a bit slow today. Are you...

    Hi Robbie. Sorry. I'm a bit slow today. Are you tagging these as 55-57? OEM 24599-55. Regards Steve
  8. Replies
    9
    Views
    654

    Strike my last comment "unfinshed stock?" These...

    Strike my last comment "unfinshed stock?" These are hardened and they wouldn't do that with an 1/8" still needed to come out.
  9. Replies
    9
    Views
    654

    Hi Robbie. Thanks for the information. No...

    Hi Robbie. Thanks for the information.
    No circlip grooves. It has the later style grub screw recesses in both sides. Maybe unfinished stock??

    28402
  10. Replies
    9
    Views
    654

    Pinion races

    Hi. Hope everyone is well.
    I have a couple of NOS pinion races which were an impulse purchase from ebay some years ago. Might have been from easyruss who I liked buying from.
    All external...
  11. Replies
    2
    Views
    339

    Before you fit the lock, make sure the drain hole...

    Before you fit the lock, make sure the drain hole is clear. It is drilled from the underside of the neck. If the frame has been blasted it could be blocked with media, paint or powder coat. Use a...
  12. 28070 Wrong pic in previous post. This is all...

    28070

    Wrong pic in previous post. This is all 3 methods.
  13. 28066 First part of the job went well. Out of...

    28066

    First part of the job went well. Out of curiosity I tried 3 methods of removing the rivet heads.
    First method was the mill.
    The machine was free of jobs and still had a 4 tooth end...
  14. Thanks for the laugh Chris. I put a laughing face...

    Thanks for the laugh Chris. I put a laughing face emoji at the start of my comment but now it looks like two question marks?

    Thanks for the instruction and tool picture Cotton. I think the...
  15. ��thanks Chris. I browsed through the purple...

    ��thanks Chris.
    I browsed through the purple workshop manual but couldn’t see a reference to this job. Was thinking/hoping there might be a shop dope or something. I would like to try and re use...
  16. Is the procedure for rear sprocket change documented in the genuine manual?

    Hi. Has anyone seen pictures or text of the factory method of the riveting procedure of the rear sprocket and dust cover. I looked but it might be posted under "A prick of a job"
  17. Replies
    24
    Views
    2,716

    Hi Steve. Apologies for the slow reply. The...

    Hi Steve. Apologies for the slow reply.
    The knurled thumb screw part number is 1413-36. I think there were 4 used on the round cover, and 2 on the hair dryer.

    I could have shown a picture of...
  18. Replies
    24
    Views
    2,716

    There is a 35 to 37 6” round air cleaner which...

    There is a 35 to 37 6” round air cleaner which has knurled thumb screws to hold the cover to the backing plate. The 38-40 6 inch cleaner is a J hook cleaner and it has the script your describing.
  19. Replies
    4
    Views
    642

    Thanks Bob. I really appreciate the info. ...

    Thanks Bob. I really appreciate the info.
    Thanks for the page number Robbie. Unfortunately I don’t have a book.
    Regards Steve
  20. Replies
    4
    Views
    642

    Thanks Steve. I have a few different springs of...

    Thanks Steve. I have a few different springs of differing lengths but they don’t have part numbers on them. The older parts manuals give description about everything in the back couple of pages......
  21. Replies
    4
    Views
    642

    Brake spring lengths

    Hi.
    Im piecing a bike together and currently working on the front and rear brakes to get the frame up on its wheels. Has anyone got a list, or know the free lengths of any of the brake springs? ...
  22. [QUOTE=Sargehere;184348]https://photos.smugmug.com...

    [QUOTE=Sargehere;184348]https://photos.smugmug.com/37-Harley-UL/n-N8tPhs/i-xCNSJ8z/0/424748c7/X2/i-xCNSJ8z-X2.jpg
    I didnt look closely at the picture of the right side. If we're all using the...
  23. The front lower tank mount is electrode welded...

    The front lower tank mount is electrode welded instead of brazed. If the frame and engine are an original set, then Harley had started using the frame that is commonly associated with 1938 which also...
  24. Replies
    12
    Views
    2,036

    Hi Chris. What is your opinion on chrome vs cad...

    Hi Chris. What is your opinion on chrome vs cad plate on 36 and 37
  25. Replies
    14
    Views
    2,477

    Hi Larry. There is a lot of years of corrosion...

    Hi Larry. There is a lot of years of corrosion that has mottled the evidence of machining marks. The area where the axle adjuster hole comes through the rib, still has the semi circular pattern of...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4