Search:

Type: Posts; User: dustydog

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    708

    Tell your friend to buy the bike and enjoy it....

    Tell your friend to buy the bike and enjoy it. It’s a wonderful motorcycle. Don’t worry about it being politically correct.
  2. Take file to those worn notches. Then the ears on...

    Take file to those worn notches. Then the ears on the screws will stay in the notches.
  3. Thread: Fork springs

    by dustydog
    Replies
    1
    Views
    237

    Fork springs

    Who makes the best fork springs for the Hydraglides
  4. It’s a satisfying job to get done. Pacific Mike...

    It’s a satisfying job to get done. Pacific Mike on you tube has a good video on a Harley rim. It’s worth a look.
  5. Buchanan spoke recommends 80 inch pounds for a 16...

    Buchanan spoke recommends 80 inch pounds for a 16 inch wheel. I think the 21 would be a lot less, maybe in the 50 inch pound range.
  6. Replies
    5
    Views
    547

    You’re not kidding. That is a huge difference. I...

    You’re not kidding. That is a huge difference. I think I know what happened now. The sprocket didn’t hit and wear into the 6 sided stud 34895-79. Someone ground it down to make clearance for the...
  7. Replies
    5
    Views
    547

    I wonder what the difference in diameter is from...

    I wonder what the difference in diameter is from a 21 to a 23.
  8. Replies
    5
    Views
    547

    Trans sprocket clearance

    Iím working on a 79 xlh and the 23 tooth trans sprocket is hitting the sprocket cover stud just to the rear it. This is the 6 sided extension that the cover bolts to. The motor mount looks to be...
  9. The timing Mark is in the right spot. Now with...

    The timing Mark is in the right spot. Now with the timing fully advanced the points should just open. Rig a test light up across your points to see if you have it right. You don’t say which way you...
  10. Replies
    4
    Views
    644

    That looks like a 34 VL muffler and yes they are...

    That looks like a 34 VL muffler and yes they are being reproduced. Replicant metals has them.
  11. Replies
    9
    Views
    933

    Also, NAPA has the crimp on style

    Also, NAPA has the crimp on style
  12. Replies
    9
    Views
    933

    Try Rhode Island Wiring Supply

    Try Rhode Island Wiring Supply
  13. Replies
    2
    Views
    481

    Thanks Chuck for your response

    Thanks Chuck for your response
  14. Replies
    2
    Views
    481

    Aermacchi sprint oil

    What sort of oil does a 1974 Aermacchi Sprint use? And donít say olive oil. Anybody know?
  15. Replies
    1
    Views
    683

    It must be a very intelligent Chief.

    It must be a very intelligent Chief.
  16. Replies
    6
    Views
    592

    The one black wire from the distributor to the...

    The one black wire from the distributor to the neg. post on the coil is all you need. I don’t know why you have another wire there. Another wire runs from the coil pos. Post to the ignition switch....
  17. I sent you a PM

    I sent you a PM
  18. The spacer and large bearing go into the case....

    The spacer and large bearing go into the case. The main drive gear goes into the bearing up to it’s shoulder and stops. The main shaft goes into the main drive gear up to it’s shoulder and stops. No...
  19. Replies
    10
    Views
    1,160

    Try Bill’s custom cycles in Bloomsburg, Pa

    Try Bill’s custom cycles in Bloomsburg, Pa
  20. Replies
    5
    Views
    601

    It might take more than 2 beers.

    It might take more than 2 beers.
  21. Replies
    5
    Views
    601

    Steve you have two different spirals right now....

    Steve you have two different spirals right now. You need to get another one like your throttle. It is hard to picture in your head but remember, the same spiral that pushes when used on one side will...
  22. Replies
    15
    Views
    1,879

    And don’t look down the bore of the tube

    And don’t look down the bore of the tube
  23. Replies
    15
    Views
    1,879

    Thank you everyone for all the replies

    Thank you everyone for all the replies
  24. Replies
    6
    Views
    799

    It was a beautiful day today. Will be nice again...

    It was a beautiful day today. Will be nice again tomorrow
  25. Replies
    15
    Views
    1,879

    Yeah thatís the problem. The plug hole is not...

    Yeah thatís the problem. The plug hole is not directly over the top of the piston.
Results 1 to 25 of 113
Page 1 of 5 1 2 3 4