Search:

Type: Posts; User: PaulCDF

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    228

    Max; Some years ago I had the pleasure of a...

    Max;

    Some years ago I had the pleasure of a 1970 HD Servi-car.
    Needed to pull the drums and after too much struggle purchased off Amazon:

    OTC (7394) Universal Hub Puller

    Bought largely...
  2. Replies
    6
    Views
    340

    Thanks; that's what I was thinking; Make some...

    Thanks; that's what I was thinking;
    Make some inserts from hot rolled steel and braze them in. Thanks again.
  3. Replies
    6
    Views
    340

    Yes the close I look at it I have come to the...

    Yes the close I look at it I have come to the realization its been "buggered" with. Disappointing.
    Hey why shorten your chain when you can extend the axle slot!
    Now how to fix?
  4. Replies
    6
    Views
    340

    Yes that is a picture of my rear section exactly...

    Yes that is a picture of my rear section exactly EXCEPT on mine the Axle slot is open.
    Instead of a closed slot/box for the axle mine is OPEN in the rear (right in picture above) (end opposite axle...
  5. Replies
    6
    Views
    340

    741 Frame question

    I recently acquired the rear section of a 741 frame.
    Looking it over serial number, below left axle hole though hard to read indicates 30.5 cu inch Army (7) Mfg 1941 (41)
    Odd thing is axle slot is...
  6. Replies
    6
    Views
    350

    I SHOULD have thought of RIW!!!!

    I SHOULD have thought of RIW!!!!
  7. Replies
    1
    Views
    267

    Specialty tools for Indian 741

    Specialty tools for Indian 741
    GREAT QUALITY and SERVICE
    Big Thanks to Mark Barthelmie at Crazy Horse Indian Australia
    Located "Down under" so shipping takes time but worth the wait.
    Good People.
  8. Replies
    6
    Views
    350

    I am thinking of 'up grading' myself to offset...

    I am thinking of 'up grading' myself to offset pin sockets.
    Kiwi Indian does not have anything listed in the catalog but, I am sure if you contacted them they could help you.
    I find the following...
  9. Replies
    3
    Views
    300

    Thanks Cotten!!! I figured you would know. You...

    Thanks Cotten!!!

    I figured you would know. You are the TRUE "Linkert Whisperer"
  10. Replies
    3
    Views
    300

    Linkert Carb Question for 741

    I am piecing together a non-matching numbers Indian 741 (Seemed like a good idea at the time).

    Learning that parts for this model are harder to come by than those for Chiefs or so it seems to me....
  11. Replies
    3
    Views
    288

    ziggysmotorworks po box 181 sandgap ky 40481...

    ziggysmotorworks
    po box 181
    sandgap ky
    40481
    360 871-8120 shop phone
  12. Replies
    3
    Views
    288

    Found this: ...

    Found this:

    http://www.vintagecyclebay.com/detail.asp?id=90719&n=NOS1934-42-Indian-Scout-Dispatch-Tow--Tow-Bar-Parts

    Good Luck
  13. BRILLANT! Thanks Wish I had thought of it!!!!

    BRILLANT!
    Thanks Wish I had thought of it!!!!
  14. Proper screwdriver to use for the primary chain adjustment?

    Question:

    For 1946 Chief;
    What is the proper screwdriver or bit to use for the primary chain adjustment?

    Most screw drivers I have will not fit within the Primary Chain Adjustment nut
    OR are...
  15. Replies
    3
    Views
    278

    THANKS Cotten; That is what I will do.

    THANKS Cotten;
    That is what I will do.
  16. Replies
    3
    Views
    278

    Questions about Carburetor Adjustment:

    Per Repair and Overhaul Manual

    Step 4.
    Prime and start the engine and allow it to warm up.
    When it is throughly warmed, check to make sure the
    choke lever is raised to the open position.
    ...
  17. Replies
    0
    Views
    194

    Link to titled 741 engine on ebay

    Link to titled 741 engine on ebay

    https://www.ebay.com/itm/1941-Indian-Military-Scout-741-Titled-Engine-Cases-Cylinders-Cam-Cov-and-Heads/143659886359?hash=item2172cbe717:g:pR8AAOSwh9de6Agk
    ...
  18. Replies
    6
    Views
    518

    "Teachable moment"

    Well this just proves that for important things I can NOT rely on my memory
    I was WRONG.

    Took a look in the garage (kept one of the old oil containers)
    Actually

    PENNGRADE
    High Performance...
  19. Replies
    6
    Views
    518

    My builder supplied me with Brad Penn...

    My builder supplied me with Brad Penn conventional 50W Break-in oil: 3 Qts.
    Changed that at 500 miles and have been using Valvoline VR1 conventional 50w high zinc
    since. Change often.
  20. Replies
    10
    Views
    761

    Thanks for the update Mike. Appreciate all the...

    Thanks for the update Mike.
    Appreciate all the hard work you have done for us in general and me in particular.
  21. So I am wondering; As the situation " is two...

    So I am wondering; As the situation " is two stand alone websites":
    Who controls the Virtual Library???
    What is the criteria for material inclusion/addition to the Virtual Library??
    Thanks.
  22. Replies
    100
    Views
    16,869

    Beautiful Dana!

    Beautiful Dana!
  23. Replies
    100
    Views
    16,869

    Dana; I have found riding motorcycles is a...

    Dana;
    I have found riding motorcycles is a "perishable skill" and riding antiques even more so.
    living in Central NY with it long winters seems every spring I have to relearn and start with
    a...
  24. Replies
    0
    Views
    183

    741 Indian Frame sections

    I am looking to buy front and/or rear frame sections for my 1941; 741 engine and transmission. Thanks.
  25. Replies
    151
    Views
    27,708

    Plan B: May be to find someone capable of...

    Plan B:

    May be to find someone capable of custom casting & machining service using old right hand case as a pattern.

    But; I am hoping you find a replacement.
Results 1 to 25 of 92
Page 1 of 4 1 2 3 4