Search:

Type: Posts; User: Omarttentmaker

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    25
    Views
    937

    current member magazine

    Haven't yet received the current issue of the club mag. Anybody else, or do I need to contact somebody?
  2. Replies
    5
    Views
    233

    OK. Thanks for the info.

    OK. Thanks for the info.
  3. Replies
    5
    Views
    233

    Thanks, Jerry. Hoping that somebody out there...

    Thanks, Jerry. Hoping that somebody out there with an unmolested '68 might be able to add to that, maybe with a description or pics of some the the nuts and bolts.
  4. Replies
    5
    Views
    233

    shovelhead hardware

    Will be putting a new face on my '68 this winter. Anybody aware of the proper hardware for this model year? Was the MOCO still using Chandler nuts and bolts, or had they been phased out by this time?...
  5. Replies
    10
    Views
    682

    I subscribed to that rag years ago in my...

    I subscribed to that rag years ago in my "chopper" phase. I considered it more of a humor magazine than a "tech mag".
  6. Replies
    0
    Views
    216

    Beck coil wiring

    Got an old Beck coil I'd like to put on my flathead. Wondering how the wires are attached. Some Beck coils that I've seen are marked + and - at the wiring studs, but this one is not. When looking at...
  7. Replies
    2
    Views
    213

    It's an OEM dash that's seen better days. Is...

    It's an OEM dash that's seen better days. Is there a chance that the socket has lost its insulation? If I test between the socket and the dash itself, it shouldn't show continuity. Haven't done that...
  8. Replies
    2
    Views
    213

    wiring oil signal light

    I gotta ask this because I think there's a mistake in the wiring diagram in the manual. On page 171 there's a wiring diagram for '49-'54. A black wire comes off terminal 5 on the dash switch, and it...
  9. Replies
    0
    Views
    284

    What a difference a year makes

    I took this pic last year on October 1. Had it posted on the CAImag. site. My knuckle and my buddy's VL.

    29825

    Took the same ride this year yesterday. Note the leaf color change. We had a...
  10. Replies
    5
    Views
    574

    The ones I'm working on don't have a shoulder in...

    The ones I'm working on don't have a shoulder in the bore, so I guess I'll just press the rubber assemblies in until the steel sleeve is flush with the bottom of the riser. Thanks for the info.
  11. Replies
    5
    Views
    574

    question about vibration dampeners

    Is there a dimension recommended as to how far to press rubber dampeners into glide risers? Maybe how far out the cup washer extends out from the bottom of the riser?
  12. Unbelievable! Just scanned through the book and...

    Unbelievable! Just scanned through the book and found out that Evans Power Cycle was at one time owned by the place in Rochester where I did my apprenticeship. It started as Morley Machinery. Mr....
  13. Replies
    10
    Views
    1,038

    I have been enlightened by the panhead manual. On...

    I have been enlightened by the panhead manual. On page 170 there is information re/ an upgraded pinion shaft that was introduced in late '51. This shaft is larger in diameter so that the pinion gear...
  14. Replies
    3
    Views
    264

    OK. Thanks for the tips.

    OK. Thanks for the tips.
  15. Replies
    3
    Views
    264

    generator gear lash

    So, the only way to set the lash is with the timing cover removed. But then you can't mount the generator with the screws without "MacGyvering" spacers with countersunk ends to accept the screw...
  16. Thread: Sparks

    by Omarttentmaker
    Replies
    7
    Views
    682

    I contacted Champion years ago, and a factory rep...

    I contacted Champion years ago, and a factory rep told me that the U stood for use with unleaded fuel.
  17. Replies
    4
    Views
    444

    You are correct, Robbie. My mistake!

    You are correct, Robbie. My mistake!
  18. Replies
    10
    Views
    1,038

    Talked to the shop I bought the parts from. He...

    Talked to the shop I bought the parts from. He said he'd contact s&s tomorrow. I told him to send the pics of the measurements I took. I doubt it'll do any good. Will keep everybody posted on this...
  19. Replies
    10
    Views
    1,038

    LOL. I'm not all that hip to internet jargon!

    LOL. I'm not all that hip to internet jargon!
  20. Replies
    10
    Views
    1,038

    Hey, kitabel, who is IIRC? Bought the upgrade oil...

    Hey, kitabel, who is IIRC? Bought the upgrade oil pump drive gears from S&S, and the one that goes on the pinion shaft is too small to fit on the shaft. From what I can measure, the shaft is .848"...
  21. Replies
    4
    Views
    444

    When I said "looking", I meant at the assembly...

    When I said "looking", I meant at the assembly drawing in the spare parts book. The part number is 71098-38, and it is described as a screw insulator. The dash number would indicate that it was used...
  22. Replies
    4
    Views
    444

    wiring question

    Looking at the pieces that make up the assembly for the fiber board that goes between the top and bottom trees on a glide. Why is there an insulated washer under the head of the screw? the board is...
  23. Replies
    10
    Views
    1,038

    Got it now. Saw the replacement stuff in the s&s...

    Got it now. Saw the replacement stuff in the s&s catalog. thanks for the input.
  24. Replies
    10
    Views
    1,038

    oil pump drive gears upgrade

    Looking to put the bigger oil pump drive gears in a '52 FL motor. H-D doesn't make them any more. Does anyone know an after-market manufacturer who does? I know they come as a pair, one that goes on...
  25. Replies
    18
    Views
    1,546

    I'd be interested in a couple pics if you so...

    I'd be interested in a couple pics if you so desire. Interesting that the top is vinyl and the skirt is leather. I've been tracking one on FleaBay that has a leather top and a plastic skirt, and the...
Results 1 to 25 of 158
Page 1 of 7 1 2 3 4