Search:

Type: Posts; User: danf19

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    108

    Splitdorf Manual

    Ive been looking for this for a while now. Just lost out on ebay. Does anyone have a copy or repop it ??
    thanks
    Dan29007
  2. Thread: excelsior oil

    by danf19
    Replies
    8
    Views
    457

    cant help answer your question but im doing the...

    cant help answer your question but im doing the same rebuild. Any advice ? did you lighten your flywheel ??
    PM Sent
    Thanks
    Dan
  3. Replies
    1
    Views
    255

    Reusing the Original Pistons, etc. ???

    I've been asking a few questions about rebuilding a 1917 excelsior motor . I have nice resleeved (I was told) cylinders measuring 3.3545" (measured by myself using a bore gage). I also have a few...
  4. PM Sent Dan

    PM Sent
    Dan
  5. Replies
    1
    Views
    153

    Flywheel BAlancing/Truing Stand

    I thought I'd ask before attempting to build one or purchase elsewhere. I am looking for a flywheel truing stand or parallel rods with a base. I am looking for something a little deeper to handle...
  6. Replies
    1
    Views
    152

    Fly Wheel Balncing Stand

    Before I attempt to make my own, I thought I'd ask. I am looking for a flywheel balancing stand that I could use with rods and pistons thus a little deeper than your typical Harley truing stand - at...
  7. thanks guys for the response. I have set up the...

    thanks guys for the response. I have set up the lathe to act as a balancing stand but also started to build a stand with the round stock as was recommended. I do have the original pistons and pins...
  8. Engine Rebuilding - Flywheel Balancing , Fitting Pistons, Torque ( Excelsior 17/18)

    I seem to have a bit of time on my hands nowadays. I've always wanted to learn to rebuild an engine. I have some pretty good components and everything will be original except the pistons (excelsior...
  9. Replies
    9
    Views
    786

    Construction of Old Fuel Tanks

    Not the best category but I couldn't find a better. Perhaps this has been covered before and if so I apologize - I don't see anything when I search.
    My question concerns the construction of old fuel...
  10. Replies
    2
    Views
    241

    I tried sending a pm but your box is full. Send...

    I tried sending a pm but your box is full.
    Send me a pm please.
    Dan
  11. Thread: indian model K

    by danf19
    Replies
    5
    Views
    589

    Not a problem ...probably better below in Indian...

    Not a problem ...probably better below in Indian other. I think Robbie's in the ballpark in terms of fuel mixture ...ive read between 20 and 25 to 1.
    I am working on one myself so sent you a pm via...
  12. Thread: indian model K

    by danf19
    Replies
    5
    Views
    589

    Mike: pm sent, Dan

    Mike:
    pm sent,
    Dan
  13. 1917 Indian Model O shifter ad Shifter Gate

    I am looking for a shifter and shifter gate for a 1917 indian model O .
    Would like to purchase one or even see a picture of one to try to make a copy.
    thanks
    Dan
  14. Replies
    0
    Views
    191

    Indian Model O Shifter and Shifter Gate

    I am looking for a shifter and shifter gate for a 1917 indian model O .
    Would like to purchase one or even see a picture of one to try to make a copy.
    thanks
    Dan
  15. Replies
    5
    Views
    727

    Stan: I love the opposed and have been trying to...

    Stan:
    I love the opposed and have been trying to piece together a model k (single) for years now,
    Dan
  16. Thread: Excelsior Motor

    by danf19
    Replies
    5
    Views
    1,564

    Great motor! I'd love to see more pictures of...

    Great motor! I'd love to see more pictures of other side and internals. please keep me in mind if you decide to sell it.
    thanks
    Dan
  17. thanks ! these are made out of steel and for a...

    thanks ! these are made out of steel and for a 1913/14 twin. Does anyone know what the original thickness of the steel was ? Made by Dale Stoner of Ohio. I'm very pleased.
    thanks
    Dan
  18. I finally got my sheaves back and pretty happy...

    I finally got my sheaves back and pretty happy with them. 2 new ones and the original fixed.
    Any thoughts ? I'm pretty pleased ! it was tough to measure the thickness consistently of the original...
  19. Replies
    0
    Views
    293

    Front and Rear Hub 1916 Miami

    I am looking for an eclipse front hub and a musslemen rear hub for my 1916 maimi. I posted pictures above in American other.
    thanks
    Dan
  20. Replies
    1
    Views
    710

    I have since found out that yes the front is an...

    I have since found out that yes the front is an eclipse - as used on other bikes of that era but the rear is a musslemen .
    Any help is appreciated,
    thanks
    Dan
  21. Replies
    1
    Views
    710

    Front and Rear Hub for a 1916 Miami

    255932559425595

    These hubs are for a 1916 maimi. I believe they are eclipse hubs (36 spokes) but want to double check. Does anyone have parts to spare or recommend repop parts (original preferred)...
  22. still trying to ...another pm sent Dan

    still trying to ...another pm sent
    Dan
  23. Kyrstin: another pm sent Dan

    Kyrstin:
    another pm sent
    Dan
  24. Kyrstin: PM sent. Dan

    Kyrstin:
    PM sent.
    Dan
  25. Replies
    0
    Views
    402

    Early Belt Drive Sheave - Twin

    Anyone have a Sheave for an early bely drive twin excelsior. I know its a long shot. If not, does Anyone have any tips on who's making them or how to make one ??
    As always, thanks
    Dan
Results 1 to 25 of 179
Page 1 of 8 1 2 3 4